User manual ZINWELL ZWA-G120

[. . . ] Wireless LAN Device Series Multi-Mode AP ZWA-G120 User's Manual Version. 1. 4. 0c (2006. 09. 14) TABLE OF CONTENTS NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 PREFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 CH 1. ZWA-G120 INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 PACKING LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 HARDWARE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 CH 2. FIRST TIME CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 BEFORE START TO CONFIGURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 KNOWING THE NETWORK APPLICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 BASIC SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 ADVANCED SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 CONFIGURING WIRELESS SECURITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 CONFIGURING AS WLAN CLIENT ADAPTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 QUICK START TO CONFIGURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 MAC CLONE FOR SINGLE ETHERNET CLIENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 CONFIGURING UNIVERSAL REPEATER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 CH 3. [. . . ] While you use this device act as AP-Client and only one host connect to this device via Ethernet, you need to check this option in this page, otherwise the other device can't recognize your host behind AP-Client. If you use hub/switch connect multi-device to this AP-Client, you should uncheck this option. 39 1 2 3 4 Configuring Universal Repeater This device can be configured as a Repeater. In this mode, the device can extend available wireless range of other AP let user can link the network that they want, Also the device working as AP and Repeater same time. Enable Universal Repeater Mode and then select a SSID in the Table that you want. (Click Refresh button to make table renew) 40 1 2 3 5 4 6 Note: Under APWDS and AP+WDS mode, The Universal Repeater can take effective. Enter specific SSID in the Extended SSID field and then click Apply Changes button to take effective. 1 2 3 4 41 Ch 3. Configuring WDS Wireless Distribution System (WDS) uses wireless media to communicate with the other devices, like the Ethernet does. This function allows one or more remote LANs connect with the local LAN. To do this, you must set these devices in the same channel and set MAC address of other devices you want to communicate with in the WDS AP List and then enable the WDS. When you decide to use the WDS to extend your WLAN, please refer the following instructions for configuration. When the WDS function is enabled, all wireless stations can't connect the device. If your network topology has a loop, you need to enable the 802. 1d Spanning Tree function. You don't need to add all MAC address of devices existed in your network to WDS AP List. WDS AP List only needs to specify the MAC address of devices you need to directly connect to. The bandwidth of device is limited, to add more bridging devices will split the more bandwidth to every bridging device. WDS network topology In this section, we will demonstrate the WDS network topologies and WDS AP List configuration. You can setup the four kinds of network topologies: bus, star, ring and mesh. In this case, there are five devices with WDS enabled: WDS1, WDS2, WDS3, WDS4 and WDS5. Bus topology: Device WDS1 WDS2 WDS3 WDS4 WDS5 Entries of WDS AP List The MAC Address of WDS2 The MAC Addresses of WDS1 and WDS3 The MAC Addresses of WDS2 and WDS4 The MAC Addresses of WDS3 and WDS5 The MAC Address of WDS4 Spanning Tree Protocol Required No No No No No 42 Star topology: Device WDS1 WDS2 WDS3 WDS4 WDS5 Entries of WDS AP List The MAC Addresses of WDS2, WDS3, WDS4 and WDS5 The MAC Address of WDS1 The MAC Address of WDS1 The MAC Address of WDS1 The MAC Address of WDS1 Spanning Tree Protocol Required No No No No No Ring topology: LAN 1 WDS #1 LAN 5 WDS #5 WDS #2 LAN 2 WDS #4 WDS #3 LAN 4 LAN3 Device WDS1 WDS2 WDS3 WDS4 WDS5 Entries of WDS AP List The MAC Addresses of WDS2 and WDS5 The MAC Addresses of WDS1 and WDS3 The MAC Addresses of WDS2 and WDS4 The MAC Addresses of WDS3 and WDS5 The MAC Addresses of WDS4 and WDS1 Spanning Tree Protocol Required Yes Yes Yes Yes Yes 43 Mesh topology LAN 1 WDS #1 LAN 5 WDS #5 WDS #2 LAN 2 WDS #4 WDS #3 LAN 4 LAN3 Device WDS1 WDS2 WDS3 WDS4 WDS5 Entries of WDS AP List The MAC Addresses of WDS2, WDS3, WDS4 and WDS5 The MAC Addresses of WDS1, WDS3, WDS4 and WDS5 The MAC Addresses of WDS1, WDS2, WDS4 and WDS5 The MAC Addresses of WDS1, WDS2, WDS3 and WDS5 The MAC Addresses of WDS1, WDS2, WDS3 and WDS4 Spanning Tree Protocol Required Yes Yes Yes Yes Yes WDS Application Wireless Repeater Wireless Repeater can be used to increase the coverage area of another device (Parent AP). Between the Parent AP and the Wireless Repeater, wireless stations can move among the coverage areas of both devices. When you decide to use the WDS as a Repeater, please refer the following instructions for configuration. You must set these connected devices with the same radio channel and SSID. Using the bus or star network topology. 44 Ethernet Wireless station AP Repeater Description Access Point Repeater Entries of WDS AP List The MAC Address of Repeater The MAC Address of Access Point Spanning Tree Protocol Required Yes Yes Wireless Bridge Wireless Bridge can establish a wireless connection between two or more Wired LANs. [. . . ] The preferred AP list will be preserved for the next use. Firmware Upgrade Firmware Types The firmware for this device is divided into 2 parts, one is web pages firmware the other is application firmware, and the naming usually are g120webpages_adv. bin and g120linux_adv_led1. bin. To upgrade firmware, we suggest user first upgrade the application firmware then web pages firmware. Upgrading Firmware The Web-Browser upgrading interface is the simplest and safest way for user, it will check the firmware checksum and signature, and the wrong firmware won't be accepted. After upgrading, the device will reboot and please note that depends on the version of firmware, the upgrading may cause the device configuration to be restored to the factory default setting, and the original configuration data will be lost! [. . . ]