User manual ZENITH P42W22H OPERATING GUIDE

[. . . ] For future reference, write down the serial number on the back of the Monitor in the space provided below. PLASMA DISPLAY PANEL Model number : Serial number : P42W22 P42W22B P42W22H OWNER'S MANUAL ON/OFF INPUT SELECT VOLUME Colored dots on the screen A PDP (Plasma Display Panel), depending on its size, contains from 0. 9 to 2. 2 million individual cells. Even with advanced technology it is inevitable that a few defective cells may be found in the PDP. We continually strive to minimize the number of defective cells but the existence of a few such defects will not be considered as sufficient reason for exchange or refund. Earth wire should be connected. - If the earth wire is not connected, there is possible a danger of electric shock caused by the current leakage. - If grounding methods are not possible, a separate circuit breaker should be employed and installed by a qualified electrician. [. . . ] · Based on the input signal, the position of the picture may not change even though you have adjusted the horizontal or vertical positions. vol vol enter 24 Safety instructions Monitor Overview Picture Phase Adjustments · If the picture isn't clear after auto adjustment and especially if the characters are still trembling, then adjust the picture phase manually. · The SCREEN menu option will not be selectable if PIP is active. READY Connections Press the menu button and then use the up/down button to select the SPECIAL menu. Press the vol ( G ) button. menu up vol down Basic operation 1 2 3 Use the up/down button to select SCREEN and then press the vol ( G ) button. up vol down SPECIAL LANGUAGE ARC SCREEN SCREEN TRANSPARENCY PIP SET ID COLOR TEMP. G G G G G G TO SET Sleep timer G G Use the up/down button to select PHASE and then press the vol ( G ) button. up vol down Picture & Sound LANGUAGE AUTO. CONFIG. CAPTION V-POSITION AUTO OFF H-POSITION SCREEN PHASE PHASE RGB-OUTPUT RESET G G G G G G G G G G 30 Special features Use a vol button to adjust phase and then press the enter button. · The adjustment range of PHASE is 0 ~ 63. vol vol enter Others Initializing (Reset to factory value) · To initialize the adjusted value, select RESET with the press the G button. D / E button and then 25 Picture In Picture (PIP) function - PIP lets you see 2 different inputs (sources) on your monitor screen at the same time. One source will be large, and the other source will show a smaller inset image. - PIP works in the following resolutions; 640x480, 800x600, 1024x768 (only in Vertical frequency 60 Hz) - When you select RGB or DTV for main picture with PIP on, you can watch video, cable TV, or DVD source for sub picture. - If input source for main picture is changed while in PIP mode, sub picture will disappear. - With PIP active, not all picture formats can be used for the main/sub picture. Watching PIP (Picture-In-Picture) pip Press the pip button. · Each time you press pip or vol button, you change the PIP picture size as shown below. PIP[S] PIP [L] OFF PIP F PIP [S] G <Small PIP> PIP F PIP [L] G <Large PIP> PIP F OFF G <Off> 26 Safety instructions Monitor Overview Selecting a source input signal input select Press the input select button repeatedly in PIP mode. · Each time you press input select button, you toggle between VIDEO, S-VIDEO and COMPONENT. VIDEO S-VIDEO COMPONENT Connections COMPONENT source only works in 480i mode. Basic operation PIP INPUT F VIDEO G Sleep timer Moving the PIP (inset) picture position Picture & Sound Press the position button in PIP mode. · Each press of the position button will move the PIP picture on the screen as shown below. Special features Others 27 Picture In Picture (PIP) function Selecting sound source with PIP on - To hear main source or PIP (inset) sound source. - This function only works with the following resolutions; 640x480, 800x600, 1024x768 (only in Vertical frequency 60 Hz). - To use this function, connect PC/DTV video output to RGB-PC INPUT/RGB-DTV INPUT and connect PC/DTV audio output to AUDIO INPUT on the monitor. READY Press the menu button and then use the up/down button to select the SPECIAL menu. Press the vol ( G ) button. menu up vol down 1 2 3 Use the up/down buttons to select PIP and then press the vol ( G ) button. up vol down SPECIAL LANGUAGE ARC SCREEN TRANSPARENCY PIP SET ID COLOR TEMP. G G G G G G G G TO SET Use the up/down button to select SOUND SELECT and then press the vol ( G ) button. up vol down LANGUAGE CAPTION PIP AUTO OFF INPUT SCREEN SOUND SOUND SELECT RGB-OUTPUT POSITION G G G G G G G G SOUND [M] G SOUND [S] Use the up/down buttons to select main picture sound (SOUND [M]) or PIP picture sound (SOUND [S]) and then press the enter button. · Each time you press the up/down button, you toggle between SOUND [M] or SOUND [S]. up enter down LANGUAGE CAPTION PIP AUTO OFF INPUT SCREEN SOUND SELECT RGB-OUTPUT POSITION G G G G G G G G SOUND [M] G SOUND [S] SOUND [S] 28 Safety instructions Monitor Overview Remote Control Setup Installing batteries · Open the battery compartment cover on the back of the remote control and insert the batteries with correct polarity, match "+" with "+", and match "-" with "-". Don't mix used batteries with new batteries. Connections Basic operation Sleep timer Notes for using the remote control Make sure these are no objects between the remote control and its sensor. Signal from the remote control may be disturbed by sun light or other strong light. In this case, turn the set to other direction. Picture & Sound Special features Others 29 Turning on the Monitor - When using the remote control, aim it at its sensor on the Monitor. Turning on the Monitor just after installation 1 2 Plug power cord into power outlet correctly. Press the main ON/OFF button on the Monitor. Press the or INPUT SELECT button on the Monitor or press power on or video/pc button on the remote control to turn the Monitor on. Turning on the Monitor (power cord is still connected) 1 2 3 If the Monitor is turned off with the button on the Monitor Press the or INPUT SELECT button on the Monitor or press the power on or video/pc button on the remote control to turn the Monitor on. If the Monitor is turned off with the ON/OFF button on the Monitor · Press the main ON/OFF button on the Monitor to turn the Monitor on. If the Monitor is turned off with the remote control and also the ON/OFF button on the Monitor · Press the main ON/OFF button on the Monitor and then press the or INPUT SELECT button on the Monitor or press the power on or video/pc button on the remote control to turn the Monitor on. Tip · Adjusting sound level The volume (G) button increases the sound level and the volume (F) button G F decreases the sound level. 30 Safety instructions Monitor Overview Menu Language Selection READY Press the menu button and then use the up/down button to select the SPECIAL menu. Press the vol ( G ) button. menu up vol down Connections Basic operation 1 Use the up/down button to select LANGUAGE and then press the vol ( G ) button. up vol down SPECIAL LANGUAGE ARC SCREEN TRANSPARENCY PIP SET ID COLOR TEMP. G G G G G G G ENGLISH ESPAÑOL PORTUGUÊS FRANÇAIS Sleep timer Picture & Sound 2 Use the up/down button to select the desired language. up SPECIAL LANGUAGE ARC SCREEN TRANSPARENCY PIP SET ID COLOR TEMP. G G G G G G G ENGLISH ESPAÑOL PORTUGUÊS FRANÇAIS down Special features 3 Press the enter button to exit. Others enter 31 Checking Features - Use the remote control to make adjustments. - Select VIDEO input source menu 1 2 Press the menu button. Press the up/down button. · Each press will cycle through the menus shown below. PICTURE APC DRP CONTRAST BRIGHTNESS COLOR TINT SHARPNESS D MOVE E G G up down 100 50 50 0 50 G G G G G GNEXT AEXIT Picture Menu SOUND DASP AVL TREBLE BASS BALANCE G G G G G 50 50 0 D MOVE E GNEXT AEXIT Sound Menu SPECIAL LANGUAGE ARC SCREEN TRANSPARENCY PIP SET ID COLOR TEMP. D MOVE E G G G G G G G GNEXT AEXIT Special Menu - The Color Temperature adjustment is only available on models P42W22B and P42W22H. up vol down vol 3 Use the vol ( G ) button to select menu option to adjust, and then use the up/down or vol buttons to adjust the selected option. · Press the enter button to exit. 32 Safety instructions Monitor Overview Setting Sleep Timer Sleep Timer turns the Monitor after the preset time expires sleep Use the sleep button to set a sleep time. Each time you press the sleep button, the time setting time changes as follows: F --- G F 240 G F 180 G F 120 G F 90 G F 60 G F 10 G F 20 G F 30 G Connections Basic operation SLEEP F 30 G Sleep timer · To cancel sleep time setting, press the sleep or F / G button repeatedly to select F --- G. [. . . ] Transmission [a][ ][Set ID][ ][FF][Cr] Acknowledgement [Set ID][:][OK][x][Data][x] Data 0 1 2 3 : OK : Fan alarm : 5V down : AC down Picture & Sound 15. PIP input select (Command:e) G To select input source for sub picture in PIP mode. You can also select source using input select button on the remote control or in the Special menu. Transmission [e][ ][Set ID][ ][Data][Cr] Data 0 : AV (VIDEO) 1 : COMPONENT 2 : S-AV (S-VIDEO) Acknowledgement [Set ID][:][OK][x][Data][x] Data 0 : AV (VIDEO) 1 : COMPONENT 2 : S-AV (S-VIDEO) * COMPONENT source only works with 480i input signal. Special features * This function is "read only". Others 51 External Control Device Setup 16. [. . . ]