User manual ZENITH H25F34DT OPERATING GUIDE

[. . . ] Installation / Operating Guide | Warranty Model Numbers | H 1 9 F 3 4 D T | H20F34DT | H25F34DT | Concierge TM TVs table of contents page 5 © Copyright 2003, Zenith Electronics Corporation For Customer Support/Service please call: RECORD THE MODEL NUMBER 1-888-865-3026 www. zenith. com The model and serial number of the ConciergeTM TV are located on the back of the cabinet. For future reference, we suggest that those numbers be recorded here: MODEL NO. ____________________________________ SERIAL NO. ____________________________________ WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. [. . . ] Just press and hold MENU (about 8 seconds) until the display changes, then press 9, 8, 7, 6, then ENTER. Or, access an item directly by entering the line number, then pressing MENU. For example, to access the Sleep Timer option which is on line 15-I, press 15, then MENU. To change a setting use the Left/Right ADJ keys. 0IMCRMI038A 01. 83 01 0-I. INST. SEQ. 0 SN: XXXX-XXXXXXXX UPN: XXX-XXX-XXX-XXX XX/XX/XX TE = 10110000 Typical Installer Menu Using the Installer's Menu Items 0-I - 86-I are immediately accessible only upon entering the Installer's Menu. Their numbers, descriptions, ranges, factory default settings, and a place for listing any changes made on-site are given below and on the following pages. A Factory Menu that is intended for qualified service technicians only, is not shown. Normally Factory menu items do not require adjustment. XX-F Menu Items (Not shown here) are servicetype adjustments and only qualified technicians having specialized test equipment should access them. Installer Menu Items 0-I through 25-I Menu Item 0-I. Function INSTALLER SEQ POWER MANAGE AC ON BAND/AFC STRT CHANNEL CHAN LOCK GHOST CH START VOLUME MIN VOLUME MAX VOLUME MUTE DISABLE KEY DEFEAT IR BANKS EN. TIMER ALARM NOT USED NOT USED FEATURE LEVEL V-CHIP MAX BLK HRS CAPTION LOCK TEXT MODE FUNCTION PRE. 0/1 0/1 0 - 99 0/1 0/1 0-3 1 Zen 1 1 12 0 1 0 Leave default set 1 (1 Zen 1) Set to 1 to enable V-Chip. Value Range 0-3 0-7 0/1 0-7 0 - 255 0/1 0/1 0 - 63, 255 0 - 63 0 - 63 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 Default Value 0 0 0 0 255 0 0 255 0 63 0 1 0 0 0 1 1 1 Brief Description of Function and Comments Leave default set 0. Channel at turn-on (Set 255 to go to last Channel viewed before turn-off). Set to 1: enables TV to respond to IR codes to change Channel Bank directly. Set to 1 to enable Alarm. 206-3852 PAGE 29 Installer Menus Installer Menu Items 26-I through 63-I Menu Item 26-I. OVER RIDE OLD OCV ACK MASK POLL RATE TIMING PULSE NOT USED CAMPORT EN. NOT USED NOT USED AUTO CAMPORT NOT USED NOT USED AUTO REAR Y/C NOT USED NOT USED STRT AUX SRCE AUX STATUS DIS. COL. Value Range Default Value Brief Description of Function and Comments 0/1 0/1 0/1 20 - 169 186 - 227 1 0 0 94 207 When set to 0, limits direct access to favorite channels. communication parameter. 0/1 1 Set to 1 to enable the front AUX (Camport) input. 0/1 1 Set to 1 to enable the rear S-Video input. 0/1 1 Set to 1 to automatically switch to Camport. 0/1 0 Set to 1 to automatically switch to rear S-Video input. 0 - 2, 255 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0-7 0-7 0/1 0-7 0-7 0/1 0-7 0-7 0/1 255 0 0 0 0 0 0 0 0 6 4 0 1 7 0 4 7 0 Set the starting AUX source Set to 1 for M. P. I. Set to 1 to enable custom color for the V-Chip (Parental Control) menu. PAGE 30 206-3852 Installer Menus Installer Menu Items 64-I through 86-I Menu Item 64-I. CH-T COL NOT USED CH NOT AVBLE CH-TIME SIZE Value Range 0-7 0-7 0/1 0-7 0-7 0/1 0-7 0-7 Default Value 6 4 0 3 4 1 1 1 Brief Description of Function and Comments Custom foreground color for the V-Chip (Parental Control) menu. Custom background color for the Channel-Time display. 0/1 0/1 0 0 When set to 1 and channel override is 0, "NOT AVAILABLE" message is displayed when direct accessing a channel not in the favorite channel list. [. . . ] Refers to the jack that receives a signal from a TV, VCR or other A/V device. Multiple Protocol Interface: Zenith protocol for external control of TV through RJ11 (M. P. I. ) input jack on TV connections panel. jack is used for cloning TV's features. ) Refers to the jack that sends a signal out of a VCR, DVD, or other A/V device. 300 TO 75 OHM ADAPTER A/V DEVICE ADD AMPLIFIER ANTENNA AUTO PROGRAM DELETE INPUT JACK MONO SOUND M. P. I. OUTPUT 2ND AUDIO Second Audio Programming (SAP) is another, separate, audio channel PROGRAMMING/SAP Available with some programming. Choosing SAP often refers to listening to audio in another language, such as Spanish or French. [. . . ]