User manual YOO DIGITAL V1400

[. . . ] €¢ When using the cleaner, don’t plug up the air outlet by towel or other matters, otherwise the efficiency of dust absorbance will be influenced, and the motor will be at high risk of being burnt out. €¢ Never use the cleaner at uneven floor or ground; and be very careful when cleaning stairs to prevent the cleaner from falling down. €¢ ever absorb live stumps with the cleaner, otherwise the motor may be damaged. N T • he cleaner should be kept far away from heat sources (such as central heating, oven, etc) to avoid the distortion of plastic parts as well as the influence caused by such distortion. [. . . ] First of all, pull out the power cord from the cord reel to the needed length; insert the power cord plug into the power socket, and press down the power switch button with finger or step on it with foot; then you can control the start and stop of the cleaner. C ontrol o f suction f orce When the suction inlet is jammed by some cloth due to the over-large suction force, you can adjust the air escape pushbutton on the hose handle to control the suction force at the suction inlet, as is shown. There is a temperature controller designed in the body of cleaner motor, which can automatically cut off the power supply of motor to prevent overheating. When the air-inlet or air-outlet pipe is overloaded or blocked, the temperature of motor rises, then the temperature controller cuts off the power supply of motor automatically to make the motor cool, preventing the cleaner from being damaged. If the temperature controller is cut off, stop the cleaner immediately and pull out the power plug to make the cleaner cool, and check and remove the hair roll or other roll-like rubbish blocking the air inlet (including the hose and the spile), and replace the filter HEPA or filter gauze when necessary. After cooling the motor for 30mins, plug in the power plug and check whether the temperature controller has been reset. If the power supply of the cleaner hasn’t been cut off, the temperature controller of the motor won’t be reset even when the motor has become cool. ________________________________________________ USER’S MANUAL PULSEE COMPACT V1400 9 M aintenance o f the C leaner _________ 1. All the day-to-day maintenance and repair jobs should be done after the power plug has been pulled out. Frequently remove the rubbish from the dust barrel, so as to avoid the failure of the cleaner. Caution: be sure to wring out the wiping cloth dry for wiping, it is prohibited for water to infiltrate into electrical elements of the cleaner. When the cleaner is placed idle not in use, it should not be put directly in the sun or in a damp place. S torag e o f the C leaner ________________ Upon the completion of the operation of the cleaner, turn off its power supply, and pull the power plug out of the power socket, then step on the cord reeling button to reel in the power cord fully. Hang the floor brush onto the floor brush hook, as is shown in Figure (7). 10 USER’S MANUAL PULSEE COMPACT V1400 ________________________________________________ EN Remove the rubbish in the dust barrel frequently to avoid the failure of the cleaner. Clean the dust barrel only after the power plug of the cleaner has been pulled out; 2. Put the dust barrel over the rubbish bin (bag), press down the releasing button of the dust barrel, the bottom cover of the dust barrel will automatically fall down, and clear and empty the dust barrel, as is shown. S torag e o f the C leaner ________________ C leanin g o f f ront f ilter f or motor Warning Please make sure the power supply of the cleaner has been cut off before carrying out the following steps : 1. Ress down the handle of the dust barrel to remove the dust barrel, and P remove the cover of the front filter for motor, and then use the brush to clean the filter (sponge and filter gauze with composite coating) or place it under the cock to clean, as is shown in Figure (9/10). ________________________________________________ USER’S MANUAL PULSEE COMPACT V1400 11 Caution It is normal that the white central filter in the dust barrel may change color, which cannot affect its filtration performance. [. . . ] Check whether the power plug is inserted securely ; pull out the plug and then reinsert it in the power socket. Check whether the switch of the cleaner is in “ON” position. The suction force is re- Check whether the floor brush, the hose and the spile are jammed, duced. Check whether the air-inlet filter gauze is dusty; frequently clean rubbish or replace air-inlet and air-outlet HEPA. [. . . ]