User manual YAMADA EG-M31A-B

[. . . ] c) When unplugging the power cord from the outlet, pull by the plug head. d) Press the power key to turn the power off when you are no longer using the product. (Unplug the cable when you won't be using it for a long time) e) Don't open the cover nor touch the components inside the product. f) Don't install nor operate this product in the sunshine or nearby heat sources to protect it from overheating. [. . . ] Connecting video and audio: No. 3 Remote Control Definitions 5 6 Power: stand by/wake up(EG-M31A) Power on/off (EG-M31B) Zzz: stand by/restart(EG-M31B) TV MODE: Quick setting of TV mode 1NTSC 2PAL 480i 576i 60Hz 50Hz 4HDMI or P/Pb/Pr 720P 50Hz 5HDMI or P/Pb/Pr 1080i 50Hz 6HDMI or P/Pb/Pr 1080P 50Hz 7HDMI or P/Pb/Pr 720P 60Hz 8HDMI or P/Pb/Pr 1080i 59. 94Hz 9HDMI or P/Pb/Pr 1080P 59. 94Hz 0: AUTO mode System setup 1) During stand by, enter system setup mode. COLOR BRIGHTNESS [50%] COLOR CONTRAST COLOR HUE [50%] [50%] COLOR SATURATION [50%] 7 enter play prev next stop pause rev fwd prev slow Return to before menu Source: return to main menu r Info:Display information the movie of home : Back to its home menu Menu:Go to main menu repeat Time seek/paste subtitle :Upload and unload subtitle; edit subtitle. audio Audio switch zoom Switch movie size; Adjust picture size Page up; Page down Control volume caps/num mute delete Switch letter style Unmount CD /DVD Drive copy No. 4 Software installation and basic operations 1) Format the HDD and install the NMT software Note: Fresh setup will format the HDD , so pls remove and save the contents. You'll find the installation guide. e) Select HDD format 8 f) Warning g) Select file source h) Select USB and confirm, installation will be executed. Open the CD-R, select according to the set up steps, select nextfinish setting. 2). After settingenter start----set up---control panel, click "IFS DRIVES", enter below interface to set up partitions of ext format. 10 3). Click "my computer"; you can see the new partition of EXT format. This time, you can copy file freely. Notice: Linux Swap is the system partition of the server, it mustn't been delete and format. The other two partitions needn't be revise partition format, otherwise, system will remind user to re-setup NMT software under play mode. Select browse to seek multimedia files from your PC, and append these files into myihome, Click "ok" to save. 4). System information default is 8000, no need to revise anywhere. 13 5). Return to the main menu, you can see all the files has been save into this software already. Then the icon will appear on the monitor at the right bottom position. before 14 After finished with installation, this PC will be found in the media source. 4. Select `Network Share"default User Name is nmt, Password is 1234. 15 In the LAN, if other computers want to enter these share units, they should input the same user name: nmt, and Password: 1234. 3). MSP interface: 17 Other BT download method: copy BT seeds into USB drive. Check schedule of BT download User needn't turn on TV to check BT download schedule, just use their own computer to check. Open BT software, input unit IP address into browser http://(IP address):8883torrent/bt. cgi Notice: user can get unit IP address from "network setup" 7. Video set up. 19 20 21 Picture display interval setting: 22 9. Premise is connecting with USB DVD device. No. 5 Firmware and NMT update guide 25 New firmware and software will be put on our website: www. egreatworld. com, and 1). Firmware update Copy these three files into the USB drive, insert USB drive into USB host of unit. [. . . ] There are some mistakes on the file due to the DVD disk being destroyed, suggest not to use the bad DVD disk. USB2. 0 chipset of DVD-ROM isn't in accordance with the USB2. 0 standard. USB2. 0 cable has problem, please use the cable attached in the package. The unit can't support DTS decode at present. Q: Why there is no signal output on the monitor? [. . . ]