User manual X10 UX21A

[. . . ] 9 Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 VCR Commander II Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 BASIC SETUP When you are setting up your VCR Commander, it's important that you have all of the parts you need ready. [. . . ] The red light on the motion sensor will blink and activate the VCR Commander. Your VCR will stop recording after five minutes. ADDITIONAL OPTIONS Clearing VCR Commands Here's how to clear VCR commands from VCR Commander: 1. Press and hold the PWR button on the VCR Commander until the light flashes (if you have a VCR Commander 2 it will also beep). The red light will flash for about 8 seconds and then the light will turn off. All VCR commands are now cleared from memory. Clearing the Motion Sensor Code Using the VCR Commander Once you've programmed and tested everything, using the VCR Commander is easy. When you want to use the VCR Commander, make sure that you turn your VCR on and change the video input so that it can record your camera. You can clear the motion sensor you programmed into the VCR Commander: 1. Press and hold the PLAY button on the VCR Commander until the red light stays on. The light will stay on. Checking the VCR Commander Status The red light on the top of the VCR Commander lets you know what the VCR Commander is doing: !While the VCR Commander is waiting for motion, the red light blinks slowly, about every one and a half seconds. When motion is detected, the red light blinks quickly, about every halfsecond. While VCR Commander is recording, the red light blinks about every second. 3. The light will turn off and the motion sensor code will now be cleared from memory. Installing Batteries After you have set up your VCR Commander, you can install four C cell alkaline batteries (not included) in the battery compartment on the bottom of the VCR Commander. Leave the VCR Commander connected to power when inserting the batteries, or your learned commands will be lost. 8 9 VCR COMMANDER II (UX23A) OPTIONS VCR Commander II has three features that aren't available in the standard VCR Commander (UX21A). TROUBLESHOOTING VCR Commander Won't Learn VCR Commands If you have trouble getting your VCR Commander to learn VCR commands, first make sure that the IR emitter is not connected while you are trying to learn. You can also try changing the position of the VCR remote when learning. You may need to change the angle that you are pointing the remote, move it closer to the VCR Commander, or move it farther away. After you've made some adjustments, follow the setup steps again. If you wait too long between steps when programming, the VCR Commander will "time out" and you will need to start over. If an error occurs while programming, the VCR Commander's light will flash (VCR Commander II will also beep). Repeat the setup procedure. Programming Multiple Motion Sensors The VCR Commander II works with up to four X10 wireless motion sensors. Press and hold the UNIT button on the front of the sensor (inside the battery compartment) until the light on the motion sensor comes on solid. The light will go out after a second, and then flash twice after 2 seconds. [. . . ] It has been type tested and found to comply with the limits for remote control devices in accordance with the specifications in Sub-Parts B and C of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by unplugging the equipment, try to correct the interference by one or more of the following measures. · Reorient the antenna of the radio/TV experiencing the interference. [. . . ]