User manual WHIRLPOOL WRF532SMBB DIMENSION GUIDE
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL WRF532SMBB. We hope that this WHIRLPOOL WRF532SMBB user guide will be useful to you.
You may also download the following manuals related to this product:
WHIRLPOOL WRF532SMBB ENERGY GUIDE (117 ko)
WHIRLPOOL WRF532SMBB USE & CARE GUIDE (1539 ko)
WHIRLPOOL WRF532SMBB WARRANTY INFORMATION (93 ko)
Manual abstract: user guide WHIRLPOOL WRF532SMBBDIMENSION GUIDE
Detailed instructions for use are in the User's Guide.
[. . . ] The unit comes from the factory with the correct refrigerant charge contained in the receiver. The refrigerant charge information is for recharging, should that be necessary. All utility connections and refrigerant line connections are made at the back of the ice maker. Before beginning installation, be sure that all of the components necessary for complete assembly of the ice system are available, and are the correct components with regard to model, voltage, and finish. [. . . ] The typical batch weight at this setting is between 8. 25 and 9 pounds. CORRECT 1 1/4" SIZE CUBE
CUBES (ACTUAL SIZE)
TOO THICK
1 1/4"
socket about 2" in diameter and located left of the evaporator plates. When the machine is running, wait untIl near the end of a "harvest" cycle. Hold a flat object about the size of this service manual over the ice level sensor socket. The ice machine will start again at the point where it will maintain the ice level. Replace all panels.
September, 1993 Page 11
WRF532SMBB
ADJUSTMENTS
Adjustment Of The Timer & Switch Assembly
TIMER CAM POSITIONS
ACTUATOR MICROSWITCH
CAM & SHAFT
One complete revolution of the cam on the timer represents eight minutes. If left as factory set, four and one-half minutes comprise the freezing cycle portion during cam rotation, and the final three and one-half minutes is the defrost/harvest cycle. Rotating the shaft of the timer cam clockwise will put the ice machine in the freeze or harvest cycle. ////////////////////////////// WARNING /////////////////////////////// Disconnect electrical power supply to icemaker whenever adjustment procedures are performed. /////////////////////////////////////////////////////////////////////////////// To adjust the timer & switch assembly: 1. To start the HARVEST CYCLE: Slowly rotate the shaft of the timer and switch assembly clockwise until the actuator arm on the microswitch begins the harvest cycle.
HARVEST PORTION
FREEZE PORTION
B. The hot gases warm the evaporators, releasing the ice cubes from the ice cube molds. The hot gas solenoid valve is installed in a branch of the discharge line from the compressor, and when the timer switches the ice machine into the harvest cycle, the energized solenoid coil lifts the valve stem within the valve body, allowing the hot discharge gas to be diverted to the evaporators. High Temperature Cut Out This temperature sensor is located next to the hot gas valve, on the outlet side. During normal operation, it does not affect the ice machine, but it will shut the machine off if the hot gas line overheats. It is an automatic reset.
September, 1993 Page 13
WRF532SMBB
COMPONENT DESCRIPTION
Ice Level Control This electronic control uses sound waves to measure the distance between the bottom of the ice machine and the top of the ice in the bin. It is designed to control the machines ice production to maintain that distance. The control is adjustable so that the ice machine will maintain a certain height of ice. It will not fill any closer to the ice machine than 8", and will not work if the distance to the bottom of the bin is greater than 8 feet. Because it uses sound waves, a slight "ticking" sound can be heard coming from the bottom of the machine.
ON/OFF/WASH SWITCH
ICE LEVEL SELECTOR SWITCH
THE USER CAN SELECT THE AMOUNT OF ICE TO BE MAINTAINED IN THE BIN.
SOUND WAVES FULL
PARTIAL
September, 1993 Page 14
WRF532SMBB
COMPONENT DESCRIPTION
Electric Water Inlet Valve The water inlet solenoid valve fills the reservoir assembly with water. Excess water overflows out the overflow standpipe located at the back of the reservoir. Water Distribution System The water distribution system evenly supplies water to all cells of the evaporator plates. [. . . ] Machine runs, but will not shut off.
Ice level switch may be defective. If open, go to B above.
PARTIAL VIEW OF CIRCUIT BOARD 12-1912-01
PLUG - IN RELAY
TIMER
BIN THERMOSTAT
Electrical Shock Hazard Can Cause Personal Injury. Bin Thermostat Posts at Line Voltage.
POSTS MENTIONED IN "D" ABOVE
September, 1993 Page 23
WRF532SMBB
REMOVAL AND REPLACEMENT
TRANSDUCER 1. Twist inner portion of transducer counterclockwise and push up gently. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL WRF532SMBB
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL WRF532SMBB will begin.