User manual WHIRLPOOL W8TXNWMBB USE & CARE GUIDE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL W8TXNWMBB. We hope that this WHIRLPOOL W8TXNWMBB user guide will be useful to you.


WHIRLPOOL W8TXNWMBB USE & CARE GUIDE: Download the complete user guide (1299 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL W8TXNWMBB ENERGY GUIDE (1648 ko)
   WHIRLPOOL W8TXNWMBB DIMENSION GUIDE (87 ko)
   WHIRLPOOL W8TXNWMBB WARRANTY INFORMATION (101 ko)

Manual abstract: user guide WHIRLPOOL W8TXNWMBBUSE & CARE GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] Once your unit is installed, keep the User Manual and this Installation Guide in a safe place for future reference. Black and White units have a reversible door with a slightly contoured handle across the top. They come with a flush mounted door panel that, when removed, will accept a custom 1/4-inch thick door panel or a 3/4-inch thick full overlay door panel. Stainless Steel units are covered with a protective coating and have been ordered left- or righthand hinged. [. . . ] Stainless Steel 2075R and 2075RF units are deemed suitable for outdoor use by UL. The unit must not be located near heat-generating equipment or in direct sunlight. Figure 9 www. U-LineService. com 6 02/2005 TM 2075R Refrigerator and 2075RF Refrigerator/Freezer Side-By-Side Installation Instructions For a complete refreshment center, install your 2075R or 2075RF Model beside a U-Line Ice Maker, Combo or Wine Captain Model (see Figure 11 for typical cut-out). · Cut-out width for a side-by-side installation is the total of the widths listed under Cut-Out Dimensions in each unit's Installation Guide. For example: Placing a 2075R or 2075RF next to a 2015 series unit would require a cut-out width of: 24-3/16" + 15-3/16" = 39-3/8" Placing a 2075R or 2075RF next to a 2075 series unit would require a cut-out width of: 24-3/16" + 24-3/16" = 48-3/8" · No trim kit is required. However, 1/4-inch space needs to be maintained between the units to ensure unobstructed door swing. · Units must operate from separate, properly grounded electrical receptacles placed according to each unit's Electrical Specifications. Typical Side-By-Side Cut-Out 4 Prepare and Install Door Panel (Black and White Units Only) Two types of custom door panels can be installed on your Black or White unit to harmonize with or accent the surrounding décor: a Custom 1/4" Insert or a Full Overlay. If no custom door panel is used, go on to 5 Adjust Door. Custom 1/4'' Door Panel Insert Door Panel Preparation A custom door panel can be inserted into the doorframe. Custom door panels can be flat or raised, as long as the maximum panel thickness where inserted into the door reveal (channel) is 1/4"-thick. For raised panels, the depth of the reveal is 1/4" on all four sides. IMPORTANT Raised panels will reduce the door's 90° swing/zero clearance if the unit is installed next to a wall or similar type of structure (see Page 5). Custom 1/4" Dimensions: Width: Height: 23-1/32" 28-5/32" The door panel must not weigh more than 20 lbs. Door Panel Installation Install the insert as follows: 34-1/4" to 35-1/8" 23-1/4" 7" 1/4" Space Between Appliances 1. Remove the door shelves by first pulling shelves up at a 45° angle then straight out (see Figure 34 on Page 14). CAUTION 1-1/2" Figure 11 Use care when handling the insert. Remove the existing bottom pivot plate and replace with the Full Overlay pivot plate (see Figure 23). Figure 24 Door Panel Existing Door Existing Bottom Pivot Plate (Remove and Discard) 3. Install the pivot post into the new Replacement Bottom Hinge (using the 7/64" hex key or Phillips screwdriver) and install the hinge onto the unit. Wood Panel Bottom Pivot Plate (5/8" Longer Than Existing Bottom Pivot Plate, Flush Side Facing Out) #8-32 x 3/8" SEMS Hex Screw Two Places 4. Replace the door closure assembly onto the bottom pivot post (see Figure 25). Be sure that bosses on closers align with holes in hinge and hinge plate. Figure 23 Existing Door IMPORTANT Door panel and overlay panel must be aligned properly or the door will not operate correctly. Install the assembled panel by sliding the original door panel back into the doorframe. Replace the two-piece Modified Handle assembly and secure with the two screws removed in Step 6 under Removing Existing Door. Starting at the corners and working toward the center, push the door gasket back into place. Remove the existing hinges from the unit, saving the door closure assembly. Install the new Replacement Top Hinge onto the unit (see Figure 24). Boss #8-32 x 1/2" Flat Head Screw Three Places Wood Panel Bottom Hinge Plate (5/8" Longer than Existing Bottom Hinge Plate) Door Closure Top Door Closure Bottom Boss Pivot Post Figure 25 IMPORTANT Pivot posts must be cleaned. Position door and install the pivot post into the top hinge (using the 7/64" hex key or Phillips screwdriver). [. . . ] The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A power supply (normal household current). An individual, properly grounded branch circuit or circuit breaker is recommended. GFCI (ground fault circuit interrupter) is usually not required for fixed location appliances and is not recommended for your unit because a GFCI could be prone to nuisance tripping. See Figure 30 for recommended receptacle location. Leveling Information Note: It is recommended that the unit is level. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL W8TXNWMBB




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL W8TXNWMBB will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.