User manual WHIRLPOOL W6TXNWFWT DIMENSION GUIDE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL W6TXNWFWT. We hope that this WHIRLPOOL W6TXNWFWT user guide will be useful to you.


WHIRLPOOL W6TXNWFWT DIMENSION GUIDE: Download the complete user guide (53 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL W6TXNWFWT ENERGY GUIDE (54 ko)
   WHIRLPOOL W6TXNWFWT USE & CARE GUIDE (1299 ko)
   WHIRLPOOL W6TXNWFWT WARRANTY INFORMATION (101 ko)

Manual abstract: user guide WHIRLPOOL W6TXNWFWTDIMENSION GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] All other charges, including transportation charges for replacements under this warranty and labor costs not specifically covered by this warranty, shall be borne by you. This warranty is extended only to the original purchaser of the U-Line product. The Registration Card included with the product should be promptly completed by you and mailed back to U-Line or you can register on-line at www. U-LineService. com. The following are excluded from this limited warranty: installation charges; damages caused by disasters or acts of God, such as fire, floods, wind and lightening; damages incurred or resulting from shipping, improper installation, unauthorized modification, or misuse/abuse of the product; customer education calls; food loss/spoilage; door and water level adjustments (except during the first 90 days from the date of purchase); defrosting the product; adjusting the controls; door reversal; or cleaning the condenser. [. . . ] Be sure that the bosses on the closers align with holes in hinge and hinge plate. Tilt top of door into position in top hinge and install top hinge screw pin. Install plastic screw plugs removed in Step 2 in old hinge holes (3 each, top and bottom). 8. 9. BOSS CLRCO008 Figure 18 17 User's Manual DOOR ADJUSTMENT Your door is aligned at the factory before shipment. Occasional re-adjustment may be necessary, especially if an Overlay Panel is installed. The following procedure will correct for up to 1/4" alignment. The door should never be flush with the top of the cabinet. Even when level, the top edge of the door will be 1/8" below the top of the cabinet (Figure 19). Compare the top edge of the door (opposite the hinges) to the top edge of the cabinet and note the type (up or down) of adjustment needed. Remove the top hinge pivot pin with a 7/64" hex wrench (Figure 20) and lift door off bottom hinge pin. Be careful not to lose door closers (Figure 22). 1/8" 2. DOOR001 Figure 19 3. With door upside-down, loosen but do not remove the two hinge plate screws. UL310 Figure 20 18 4. If door edge opposite the hinges needs to move up, move plate toward outside of door. If door edge needs to move down, move plate toward inside of door (Figure 21). The compressor begins to operate and water flows over the evaporator assembly (ice cube tray). This may cause uneven sized cubes or water spilling into the ice storage bin. This is a normal situation and will correct itself within the first twenty-four hours of operation. After the initial startup period, the water will cascade evenly over the evaporator. 5. 6. C L N O F F O N C L N O F F O N After the first slab of ice is produced, ice production will stop until the refrigerator side of the CLRCO2075 reaches the set point temperature. After the refrigerator reaches temperature, ice production will begin again. It is possible that dirt or scale will dislodge in the water line. Always throw away all ice cubes made during the first two to three hours of operation. TEMPERATURE CONTROLLER 1 2 3 WARMER COOLER SET TEMP CLRCO011 Figure 28 The temperature controller (Figure 28) is located below the clear ice maker. It consists of an LED display, three LED status indicator lights and three touchpad buttons. The LED display shows the temperature set point and is calibrated in degrees Fahrenheit. The controller is factory programmed for a set point of 38°F which will show when the unit is first powered up. To display actual temperature in the refrigerator, press the "WARMER" button momentarily. [. . . ] Make sure the water supply line is not kinked. WATER SOLENOID VALVE 5. 6. HOSE CONNECTOR WATER SUPPLY LINE CLRCO013 Figure 39 7. Make sure the drain system is working properly and the drain hose is not pinched or kinked. If your CLRCO2075 is equipped with a drain pump, the pump should drain the ice bin. 35 User's Manual LIGHT BULB REPLACEMENT Light bulb replacement ÉchelonTM series is simple. in the 1 TAB Remove the light housing cover by sliding the cover toward the tab, swinging the end opposite the tab down and pulling down and away (Figure 40). [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL W6TXNWFWT




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL W6TXNWFWT will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.