User manual WACOM CINTIQ 12WX

[. . . ] Installation Guide & Hardware Manual for Cintiq 12WX (DTZ-1200W) Wacom Cintiq® 12WX Installation Guide & Hardware Manual for Cintiq 12WX (DTZ-1200W) English version 1. 0, September 13, 2007 Copyright Wacom Co. , Ltd, 2007 All rights reserved. No part of this manual may be reproduced except for your express personal use. Wacom reserves the right to revise this publication without obligation to provide notification of such changes. Wacom does its best to provide current and accurate information in this manual. [. . . ] ASPECT resizes the image to fill as much of the screen as possible while maintaining the correct aspect ratio. (VGA only. ) Choose this function to automatically optimize the display screen image. (VGA only. ) Synchronizes the signal timing of the pen display to that of your graphics card. Use this adjustment when you experience an unstable or flickering image, or horizontal distortion lines. (VGA only. ) Changes the display data frequency to match that of your graphics card. Use this adjustment when you experience an unstable or flickering image, or vertical distortion lines. Customizing Page 33 POSITION menu options (VGA only) are as follows: · VERTICAL. To automatically adjust, use the AUTO ADJUST option. COLOR menu options are as follows: · TEMPERATURE. Provides color temperature settings for 6500° and 9300° Kelvin, as well as DIRECT and CUSTOM options. · DIRECT displays the colors directly from the video card without any adjustment. After selecting the CUSTOM color option, you can independently adjust the RED, GREEN, and BLUE display colors. Note: Manual changes made to the color settings will invalidate the Cintiq color profile. OSD Control menu options are as follows: · VERTICAL. Use this option to set the amount of time the OSD menu will remain displayed with no user input. Customizing Page 34 ADJUSTING CLOCK AND PHASE (VGA ONLY) Some computers and video cards may not allow the auto-sync function to fully work when Cintiq is first connected. If some portion of text appears blurred, open the OSD menu, go to the VGA IMAGE menu, and select AUTO ADJUST. If the image is still blurred, adjust the clock and phase manually by following the procedure below. For optimal display quality, set your video card to Cintiq's native resolution of 1280 x 800 pixels. · · In the Wacom Tablet control panel, select the CALIBRATE tab. If you are working with multiple displays, be sure the display corresponding to Cintiq is selected in the MONITOR menu. Then adjust the clock level so that the pattern of fine vertical stripes displays evenly. (For details on changing the OSD settings, see On Screen Display (OSD) settings on page 31. ) Next, in the OSD menu select the IMAGE and PHASE options. Click on the CANCEL button or press ESC to exit the calibration screen. · · · · · Adjustment pattern for clock and phase. Customizing Page 35 TROUBLESHOOTING Most of the time your pen display tablet will work flawlessly. But if you are having trouble, Wacom recommends you do the following: 1. If the Wacom tablet driver failed to load properly, first perform the recommended action in any error message that may appear on your screen. If that does not solve the problem, continue with the troubleshooting procedures in this chapter. [. . . ] You should send the product, shipping charges prepaid, to the designated service location, accompanied by the return authorization number, your name, address and telephone number, proof of purchase date, and a description of the defect. Wacom will pay for return shipping by United Parcel Service or by an equivalent service as chosen by Wacom. Wacom's sole obligation and entire liability under this warranty shall be, at Wacom's option, either the repair or replacement of the defective product or parts thereof of which Wacom is notified during the Warranty Period; provided, however, that you are responsible for (i) the cost of transportation of the product to the designated service location and (ii) any loss or damage to the product resulting from such transportation. Wacom shall have no responsibility to repair or replace the product if the failure of the product has resulted from accident, abuse, misuse, negligence, or unauthorized modification or repair, or if it has been handled or stored other than in accordance with Wacom's storage instructions. [. . . ]