User manual VITEK VTC-C750WDR
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual VITEK VTC-C750WDR. We hope that this VITEK VTC-C750WDR user guide will be useful to you.
Manual abstract: user guide VITEK VTC-C750WDR
Detailed instructions for use are in the User's Guide.
[. . . ] Setup Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dimensional Drawings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setup Menu tree. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Attaching the lens · Remove the Dust Protection cap from the lens mount · Screw the lens onto the camera without using force 5. 2. Setting the back focus lock The back focus is the distance between the lens support on the camera and the image sensor. It may be necessary to set the back focus in individual cases due to production tolerances of the lens. For lenses with automatic iris control, you will require a ND filter (gray filter) to prevent the iris from closing in bright light. Setting for lenses with a fixed focal distance If the focus cannot be set exactly by turning the focus ring (lens), please proceed as follows; 1. The distance to the object should be longer than 1, 000 x the focal distance. Set the focus of lens so that the distance at the lens is close to infinity but not to exact infinity position. 7.
Loosen Back focus Adjustment Lock Screw one~two turns on the camera with industrial "+" driver Rotate Back Focus Adjustment until the optimum focus is achieved. Trim the focus precisely at lens if necessary.
Setting for lenses with a variable focal distance (zoom) If the focus changes as the focal distance changes, please proceed as follows. Point the camera at an object with sufficient contrast at a distance of approximately 2 meters. Loosen Back focus Adjustment Lock Screw one~two turns on the camera with the industrial "+" driver 7. Steps 3, 4, 5 and 7 may be needed to repeat several times to obtain the best results 8. Installation The camera has a 1/4" thread insert on its top and bottom side for mounting the camera to a tripod or the wall or ceiling with a corresponding mount. 5. 4 Commissioning · Connect the power to the camera firstly · Plug the power adaptor to the mains supply secondly · Power indicator LED will be lit · The camera is ready for operation 5. 5. Power Supply Connections Camera can work with either 12VDC or 24VAC, dual voltage power. Primary and secondary grounds are completely isolated to avoid the possible ground-loop problems. Its excellently wide operating voltage range of 10. 5V-30V for DC and 12-28. 8V for AC gives an extra flexibility at the installation.
6. Start up
When the camera is powered properly, it starts up with initializing the internal parameters and the filter switch mechanism. The filter switch unit repeats IN and OUT two times at each power up and just after RESTORE FACTORY SETTINGS.
8
VTC-C750WDR
7. SETUP Menu
7. 1 In the menu , buttons to move menu, Use to select or enter. , buttons to change the settings and press button short
button stands for MENU or ENTER button. 7. 2 Entering menu Press button longer than 2 sec on the back of camera.
7. 3 PRESET menu PRESET menu is provided to help the settings with the possible parameters obtained and assumed by the factory tests for the most common environments.
PRESETs may not be the best optimized settings for the actual installations. [. . . ] Synchronization is INTERNAL but sync frequency is modified to simulate line-lock. Line-lock for AC24V and Internal for DC12V
15
VTC-C750WDR
7. 16 SAVE / RESTORE / EXIT menu
MENU-2 SAVE AND EXIT EXIT NO CHANGES RESTORE FACTORY SETTINGS LANGUAGE VIDEO STANDARD
Descriptions Exits menu after saving the parameters. VIDEO STANDARD does NOT change by RESTORE FACTORY SETTINGS
16
VTC-C750WDR
8. Specifications
Model name Image Device Effective Pixels TV system Scan frequency. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE VITEK VTC-C750WDR
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual VITEK VTC-C750WDR will begin.