User manual VITEK VT-KBD1

[. . . ] This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. These equipments generate, use and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Please consult the Xpress Keyboard distributor or the closest Vitek customer help desk. Do not use substances containing alcohol, benzene, thinners or other flammable substances to clean or maintain the equipment. Use a dry cloth on a regular periodic basis and wipe away the dust and dirt that collects on the device. In dusty, humid or greasy environments, the dust that collects around the ventilation or the slots on the outer casing over long periods of time may become saturated with humidity and short-circuit, leading to fire. Any of these actions may cause an electrical short circuit, which may lead to fire or electrical shock. 6 VT-KBD1 Do not handle the device or power cord if the hands are wet. When unplugging the cord, ensure that you hold the solid portion of the plug. Pulling on the flexible portion of the cord may damage or expose the wire and insulation, creating the potential for fires or electrical shocks. Use of power sources not expressly recommended for this equipment may lead to overheating, distortion of the equipment, fire, electrical shock or other hazards. The supplied AC power adaptor and power cable are designed for exclusive use with the Xpress Keyboard. There is a risk of fire and other hazards. 7 VT-KBD1 CAUTION Avoid using, placing or storing the equipment in places subject to strong sunlight or high temperatures, such as the greenhouse or trunk of a car. Exposure to intense sunlight and heat may cause the battery to leak, overheat or explode, resulting in fire, burns or other injuries. Storage in such areas could lead to fire, electrical shock or other damage. Do not operate the Xpress Keyboard beyond its specified temperature, humidity or power source ratings. Do not use the Xpress Keyboard in an extreme environment such as in high temperature or high humidity. Use the device at temperatures within 41°F - 104°F and humidity below 90 %. Never place the Xpress Keyboard in close proximity to electric motors or other equipment generating strong electromagnetic fields. Exposures to strong magnetic fields may cause malfunctions or corrupt image data. Moving the equipment rapidly between hot and cold temperatures may cause condensation (water droplets) to form on its external and internal surfaces. You can avoid this by placing the equipment in an airtight, re-sealable plastic bag and letting it adjust to temperature changes slowly before removing it from the bag. If condensation forms inside the Xpress Keyboard, stop using the equipment immediately if you detect condensation. Remove the power cord from the power outlet and wait until the moisture evaporates completely before resuming use. 8 VT-KBD1 I. INTRODUCTION FEATURES The Xpress Keyboard is designed to control up to 64 Xpress Dome cameras in duplex control mode, and up to 255 Xpress Dome cameras in simplex control mode. [. . . ] The timer can be set up to 30 minutes after the last press of the button. 26 VT-KBD1 4. 1. 3 CHANGE USER PASSWORD Move the joystick to the right to access the user password change screen. Enter the current user password, and then the new password, and then confirm the new password. 4. 1. 4 CHANGE ADMIN PASSWORD Move the joystick to the right to access the administrator password change screen. Enter the current administrator password, and then the new password, and then confirm the new password. 4. 1. 5 FACTORY DEFAULT Revert back to the factory default. 4. 1. 6 SAVE AND EXIT Save the settings and return to the main menu screen. 27 VT-KBD1 4. 2 PORT Port menu configures the different communication ports on the junction box. 4. 2. 1 DOME 1 Move the joystick to the right to access the DOME 1 port setup screen. Select the device type of DOME 1 port. Select the communication speed of DOME 1 port. Save the settings and exit to the PORT menu. 4. 2. 2 DOME 2 Move the joystick to the right to access the DOME 2 port setup screen. 28 VT-KBD1 Select the device type of DOME 2 port. Select the communication speed of DOME 1 port. Save the settings and exit to the PORT menu. 4. 2. 3 SLAVE Move the joystick to the right to access the SLAVE port setup screen. Select the device type of SLAVE port. Select the communication speed of SLAVE port. Save the settings and exit to the PORT menu. 29 VT-KBD1 4. 2. 4 DVR Move the joystick to the right to access the DVR port setup screen. Select the device type of DVR port. Select the communication speed of DVR port. Save the settings and exit to the PORT menu. 4. 2. 5 ALARM Move the joystick to the right to access the ALARM port setup screen. Select the device type of ALARM port. Select the communication speed of ALARM port. 30 VT-KBD1 Save the settings and exit to the PORT menu. 4. 2. 6 EXIT Exit to the main menu screen. 4. 3 CAMERA Camera menu configures the cameras connected to the Xpress Keyboard. [. . . ]