User manual US ELECTRONICS NOVARI SA

[. . . ] US Electronics provides these function descriptions as a general guide to allow you to become more familiar with your set-top box. Refer to your set-top box manual for descriptions of specific functions. POWER is used in conjunction with the device keys to turn devices on and off SETTINGS/MENU displays current set-top box settings TV/VCR switches the VCR between TV and VCR BYPASS functions differently depending on what mode the remote control is in: · While in VCR mode, switches TV/VCR input · While in TV mode, switches TV/Video input · While in CBL mode, controls Bypass function 4-in-1 Cable TV Remote Control for Scientific-Atlanta® Explorer 2000 & 3000 Converters VISIT US ON THE WEB You can find programming instructions and codes for all of our remote controls, as well as information about our other products on our website: www. uselectronics. com POWER CBL DEVICE KEYS allow you to select which device your remote will operate. They are also used to set up the remote control TV VCR DVD AUD 2 INSTALL BATTERIES MENU P A G E TV/VCR Before you can program or operate the remote control, you must install two Alkaline AA batteries. Step 1: Remove the battery compartment cover on the back of your remote control. [. . . ] . VCR Channel Lock prevents the channel up and down functions from operating any device other than the set-top box -- no matter which device (TV, CABLE, VCR, DVD, AUDIO) is currently selected. If you want the remote control to operate channel functions on your TV or VCR you will need to de-activate Channel Lock. To deactivate Channel Lock, follow these steps: 1 2 Press and hold the CBL key for 3 seconds. Repeat these steps to re-activate Channel Lock. 1 2 On the remote control, press and hold the appropriate device key until the five device keys flash twice. After you press the first digit, the device key should light and stay on. After you press the last digit, the device key should flash three times and turn off. If the device key does not flash three times before turning off, the code is invalid for this device type. Repeat the procedure with another device code. 8 SmartScanTM If none of the codes listed for your device works, the SmartScanTM procedure will allow you to cycle through all the available codes in the remote until you find the right one. 3 Point the remote at the device and press POWER. If you have tried all the codes listed for the manufacturer and the device does not respond, refer to the CodeScanTM section later in this manual. 1 2 Manually turn on power to the device for which you want to program the remote (TV, VCR, DVD, AUDIO). Press and hold the appropriate device key for approximately three seconds until the five device keys flash twice. Approximately once every second, the remote sends the power-off command using a different device code. When the device turns off, that means that the remote has reached a code that can control the device. If you accidentally press the UP ARROW key after the device has turned off, press the DOWN ARROW key to return to the previous device code. The Up Arrow Key 4 Write the codes below 025 Set-top Box code ___ ___ ___ VCR code ___ ___ ___ 3 TV code ___ ___ ___ Audio code ___ ___ ___ DVD Code ___ ___ ___ 5 PROGRAMMING VOLUME CONTROL By default, the TV, CBL, or AUD keys will send their own volume and mute signals to their device. If you would like to set up the Novari so that volume is always controlled by a particular device (set-top box, TV, or audio amplifier), follow these steps: 4 1 2 Press and hold the CBL key for approximately three seconds until the five device keys flash twice. Press VOLUME UP then VOLUME DOWN then the Device Key (TV, CBL, or AUD) of the device that you want to control volume and mute functions. After you release the Device Key, the CBL key will blink three times to confirm the procedure. Test whether other functions operate using the remote control. If a primary function does not work, continue to press the UP ARROW key to find another code that turns off the device. When you are satisfied that all primary functions are working, press SELECT to lock in the code. 9 RECALLING A DEVICE CODE NOTE: volume will always be controlled by your audio device when the remote control is in AUD mode -- regardless of how you set up volume control in this section. Perform the following steps to read the code currently set for a device. This is useful for retrieving a device code that was set using the CodeScanTM procedure. 6 MASTER POWER CONTROL 1 2 Press and hold a device key until the five device keys flash twice. For example, three flashes represent the number 3, and a rapid flicker represents 0, so a code of 103 will be shown as: FLASH <pause> FLICKER <pause> FLASH FLASH FLASH Count and record the sequence of flashes to determine the three-digit code. You can program your Novari to turn on and off all of your remote-controlled devices (TV, CABLE, VCR, DVD, AUDIO) when you press POWER. [. . . ] Finally, make sure that nothing is blocking the signal from the remote control from reaching your TV, VCR, or set-top box; and make sure that you are pointing the remote control at the correct device when you are pressing a key on the remote. ! 14 Panasonic ReplayTV PERSONAL VIDEO RECORDER CODES 145 142 · 145 ShowStopper TIVO 145 135 · 144 · 146 ?Solution Make sure all cables are connected properly and that all devices are powered on. Consult related owners manuals for specific installation and operation instructions for each device. Solution Press the CBL key when you want the VCR/VOD keys to operate Video-onDemand (VOD) functions. [. . . ]