User manual TREK BIKES INCITE 6I-8I 2006

[. . . ] 31. 8mm bars: large clamp 25. 4mm and 26. 0mm: small clamp 22. 2mm bar: small clamp with rubber shim 2. Insert the handlebar clamp into the back of the computer base (Figure 4) and slide it towards the front of the base. Figure 4- Clamp and friction pad in computer base 3. Insert the rubber friction pad into the computer base, aligned across the computer base. With the wire pointing toward the front of the bike, wrap the bar clamp around the handlebar. [. . . ] Continue routing the wire, either by wrapping around the fork or frame tube, or attach the wire to the fork or frame tube with electrical tape. As needed, solidify the wire attachment with either nylon ties or electrical tape. Figure 8- Trim excess nylon tie length 8 Installation Attaching the sensor The magnet must pass across the line on the sensor (Figure 9). To install the sensor 1. Orient the sensor so that the clearance between the sensor and the magnet is between 1 to 3mm. If needed, the sensor and magnet can be moved up or down the spoke and fork to change the amount of clearance. Attach the sensor with nylon ties, but do not fully tighten. 1. 0 3. 0mm Figure 9- Magnet alignment and 4. With the computer in the computer base, check the alignment of the sensor clearance and magnet by spinning the wheel and noting if the computer is displaying speed. If the computer shows current speed, the sensor is reading the magnet. If the computer is not displaying a value, realign the sensor and magnet until one is displayed. Tighten the nylon ties and trim the excess length (Figure 10). Figure 0- Trim excess nylon tie length 0 Installation EASy SETuP (RESET) You can program the starting values of your computer in a single, easy procedure: · Units · Clock · Wheelsize · Odometer The Units setting tells the computer which conversion to use: metric or SAE ("English"): MH = miles KMH = kilometers You can set the clock for 12 or 24 hour display, which changes how time appears in the afternoon, such as 3PM: 12 hour clock 3:00 24 hour clock 15:00 You can set the wheel size by simply choosing from a menu listing tire sizes, or you can set custom values listed in a chart. You can set the odometer to be at "0" or you can start at a different value. This allows you to keep track of your previous mileage after the computer has Reset (started over at 0), such as after installing a new battery. Easy setup (ReSet) using the buttons When setting the computer, there are three ways to use the buttons. To help you CLK MH TME AVG remember, these terms will look the MAX TRP Set same throughout the manual. ODO Push- touch once Cycle - push repeatedly as needed Hold- push and hold in for two or three seconds Mode The buttons on the computer are Figure - Buttons on the Incite 6i computer (Figure 11): Set· button on the right side Mode button on the bottom To set the computer, you must Push, Cycle, or Hold the two buttons in a specific sequence. 2 Easy setup (ReSet) CLK TME AVG MAX TRP ODO MH Set To set the computer 1. The computer returns to the start screen. CLK TME AVG MAX TRP ODO Mode MH Figure 2- ODO screen To set 6i wheel size For 8i, go to page 14, To set 8i wheel size 1. Hold Set· Wheel size appears on the screen. Easy setup (ReSet) 3 CLK TME AVG MAX TRP ODO MH Set Note: If you want to set a custom wheel size, go to page 24 now. The computer returns to current speed. Mode To set 8i wheel size The 8i allows you to use two different wheel sizes. The icon for Wheel 2 is a partial circle surrounding the Wheel 1 icon (Figure 13). Hold Set· Wheel Select icon appears on the screen. Figure 3- Select wheel screen 3. Note: If you want to set a custom wheel size, go to page 24 now. 4 Easy setup (ReSet) CLK TME AVG MAX TRP ODO MH Set 5. To set the second wheel size, repeat the instructions, but select the other Wheel Select icon. To select the wheel for use 1. Repeat step 2 to change again. Easy setup (ReSet) 5 CLK TME AVG MAX TRP ODO MH Set Mode To set Clock 1. Push Set· to select The clock appears on the screen with the Hour flashing. [. . . ] With the valve stem of the front wheel directly over the floor Figure 18), sit on the bike. Figure 8- Measuring rollout for wheel size 2. While you sit on the bike, have the helper roll the bike forward one revolution of the wheel, so that the valve stem is again directly over the floor. If you can only measure in inches, convert to millimeters by multiplying by 25. 4. Use the result to program your computer, following the instructions on page 22. 24 Setting Custom Wheel Size lIMITEd WARRANTy Trek Bicycle Corporation warrants each new Incite computer against defects in workmanship and materials. This warranty covers Trek Incite computer models 6i, 8i, 9i, 11i, ACH, and ACH Digital for a period of two years from the date of sale. This warranty does not cover · Normal wear and tear, including the length of battery life · Improper assembly · Installation of parts or accessories not originally intended for, or compatible with the component as sold · Damage or failure due to accident, misuse, abuse, or neglect This warranty is void in its entirety by any modification of the component or its parts. [. . . ]