User manual TREK BIKES INCITE 6I-8I 2005

[. . . ] Also, the wire could get caught, causing you to lose control and fall. Figure 2- Keep the wire Figure 1- Watch the road out of the spokes when riding. © Copyright Trek Bicycle Corporation 2004 All rights reserved FUNCTIONS Not all Trek Incite computer models have all these functions. Table 1- Function abbreviations, names and explanations Function Speed Explanation Current speed of the bicycle displayed in miles per hour (MPH) or kilometers per hour (KPH). Highest readings: · 6i, 8i: 107. 3mph or 172. 7kph · 9i, 11i: 80. 5mph or 129. 6kph Time of day displayed in hours and minutes, in 12-hour or 24-hour format Amount of time elapsed since last reset. Highest readings: · 6i, 8i: 9:59:59 · 9i, 11i: 23:59:59 Highest speed since last Reset displayed to tenths. Highest readings: · 6i, 8i: 107. 3mph or 172. 7kph · 9i, 11i: 80. 5mph or 129. 6kph Amount of distance elapsed since last Reset displayed in miles or kilometers, and tenths. [. . . ] Wrap the wire around the front brake cable, diverting the determined amount. Continue routing the wire, either by wrapping around the fork or frame tube, or attach the wire to the fork or frame tube with electrical tape. As needed, solidify the wire attachment with either nylon ties or electrical tape. Figure 8- Magnet placed on crankarm, aligned with sensor on chainstay To install the sensor These instructions are written for the front wheel, but apply equally to installing the magnet and cadence sensor which go on the left crank and the frame's chainstay. Orient the sensor so that the clearance between the sensor and the magnet is between 1 to 3mm. The sensor can be rotated around the fork blade or crank about 45 degrees. If needed, the sensor and magnet can be moved up or down the fork and wheel to change the clearance. For the wireless sensor, install the rubber "foot" in the sensor (Figure 11). With the computer in the computer base, check the alignment of the sensor and magnet by spinning the wheel and noting if the computer is displaying speed. If the computer shows current speed, the sensor is reading the magnet. If the computer is not displaying current speed, realign the sensor and magnet until current speed is displayed. Tighten the nylon ties and trim the excess length (Figure 12). Figure 9- Extra wire wrapped around the brake housing 1. 0 3. 0mm Figure 10- Magnet alignment and clearance Figure 11- Wireless sensor, foot, and fork blade Figure 12- Trim excess nylon tie length Installation 3 SETTING THE COMPUTER The computer must be set, or "programmed, " so that it gives its readout in the units preferred by the user, and so that it calculates with the correct wheel size. There are three ways to use the buttons: · Push- touch once · Cycle- push repeatedly as needed · Hold- push and hold in for two or three seconds The method used to set the computer varies according to the computer model. Follow the instructions covering your computer model, grouped as follows: · Incite 6i and 8i (pages 7-9) · Incite 9i and 11i (pages 10-12) INCITE 6I AND 8I Setting the 6i and 8i is done by pushing the two buttons in a specific sequence. The large button on the bottom, which may look like two buttons, is the Mode button. To set Odometer and Wheel size By default, the odometer always starts at `0'. The computer returns to current speed. To set Custom wheel size 1. Cycle Set to the four-digit number (see Table 2). Table 2- Wheel size and corresponding settings in millimeters 700 x 20 700 x 23 700 x 25 700 x 28 700 x 32 700 x 35 700 x 38 2086 2096 2105 2136 2155 2168 2180 26 x 1. 5 26 x 1. 90 26 x 1. 95 26 x 2. 0 26 x 2. 1 26 x 2. 2 Custom 2010 2045 2050 2055 2068 2075 0000 - 2999 6. The computer returns to current speed display. Setting the computer 4 To set Clock 1. The computer returns to current speed. To Restart the trip modes The trip modes include TRP AVG, TME, and MAX. This operation sets all four values to zero, allowing , the computer to display information for a single ride. The Max setting restarts at 0. Second wheel size (Wheel 2) The following features are only on the Incite 8i. The second wheel size allows the computer to calculate using the wheel size of a second bike. For example, you can use the computer on your road bike with 700c racing wheels, then move it to your mountain bike with 26" wheels. [. . . ] Here is a table showing some possible problems, causes, and solutions: Table 4- Common problems and solutions Blank screen Computer is in shipping mode. Readjust magnet and sensor alignment. No cadence (11i) LIMITED WARRANTY Trek Bicycle Corporation warrants each new Incite computer against defects in workmanship and materials. This warranty coversTrek Incite computer models 6i, 8i, 9i, and 11i for a period of two years from the date of sale. This warranty does not cover· Normal wear and tear, including the length of battery life · Improper assembly · Installation of parts or accessories not originally intended for, or compatible with the component as sold · Damage or failure due to accident, misuse, abuse, or neglect This warranty is void in its entirety by any modification of the component or its parts. [. . . ]