User manual TREK BIKES INCITE 6I-8I QUICK START GUIDE

[. . . ] Insert the rubber friction pad into the computer base, aligned across the computer base. With the wire pointing toward the front of the bike, wrap the bar clamp around the handlebar. Tighten the screw until the computer base cannot rotate on the handlebar. Slide the computer into the computer base until the front of the computer and computer base line up. Installation 5 Check that the computer base cannot be rotated around the handlebar, and that the computer cannot slide backwards on the computer base (Figure 5). To install the computer on the stem 1. [. . . ] Slide the computer into the computer base until the front of the computer and computer base line up. Check that the computer base cannot be rotated around the stem and the computer cannot slide backwards on the computer base. Figure 6- nylon tie threaded through computer base 6 Installation 6. Tighten the nylon ties and trim the excess length. Placing the magnet The wheel magnet must be aligned so that it passes across the sensor. As the magnet passes the sensor, it must be no further from the sensor than 1 to 3mm (1/32 to 1/8 inch). The wheel magnet has a `T' shaped slot with two configurations: round spokes and flat or bladed spokes (Figure 7). To install the wheel magnet 1. For a flat or bladed spoke, start the spoke near the end where the spoke is round, and align the top of the `T' with the spoke as you slide the magnet up the blade (Figure 7). Thread the screw into the magnet until it is snug against the spoke. Figure - Installing magnet on round or oval spokes Installation Attaching the computer wire The computer wire is usually longer than needed. Extra wire length can be diverted by wrapping it around the brake housing prior to routing it down the fork blade or down tube (Figure 8). Make sure the computer wire is not pulled tight when the handlebar is turned all the way to either side. To attach the computer wire 1. Determine the length of wire to divert by holding the sensor at its desired mounting point. Wrap the wire around the front brake cable, diverting the determined amount. Push Set· to select The clock appears on the screen with the Hour flashing. The computer returns to current speed. Figure 5- CloCK screen 6 Easy setup (reSet) CLK TME AVG MAX TRP ODO MH Set RESTART- gETTINg REAdy TO RIdE Your computer stores data for two intervals- since last ReSet and since last ReStart. The trip modes include · TRP · TME · MAX This operation sets all four values to zero, allowing the computer to display information for a single ride. Mode To ReStart (set the Trip data to zero) 1. The Max setting ReStarts at `0'. F MPH CLK TME AVG MAX TRP AVG Figure 6- TrP screen reStart CLK TME AVG MAX TRP ODO MH Set AddITIONAl INfORMATION Changing mode Mode Once the computer is programmed and installed, it is very easy to use. To change to different modes (functions), simply Cycle the Mode button until the desired function appears, shown by the spelled name of the function. Removing the computer from the computer base The computer is held on its base by a flexible snap. To remove the computer, press firmly on the computer (not on the base) in a rearward direction. using the computer in wet weather Bicycle computers function on electricity. If the electrical contacts between the computer and its base become saturated, the electrical signals may become irregular or interrupted entirely. If the computer is to be used in heavy rain, etc. , we recommend that a plastic bag be put over the computer and its base. The other parts of the computer system are waterproof. 8 Additional Information TROuBlEShOOTINg The Incite 9i computer is designed to be easy to install and maintain. Table 3 shows some possible problems, causes, and solutions: Table 3- Common problems and solutions Blank screen Computer is in shipping mode. Cycle Set· to change your wheel selection from Wheel 1 to Wheel 2. 22 Setting Custom Wheel Size CLK TME AVG MAX TRP ODO MH Set 4. [. . . ] Cycle Set· to change your wheel selection from Wheel 1 to Wheel 2. 22 Setting Custom Wheel Size CLK TME AVG MAX TRP ODO MH Set 4. Cycle Mode through the wheel sizes tro the 4-digit number. Setting Custom Wheel Size 23 To measure rollout for wheel size Table 1 approximates the circumference of each tire size. Instead of using an approximation, you can measure the actual circumference of your wheel. You need a helper, your bike, and a smooth floor with enough room to roll the bike about 7 feet (245 cm) in a straight line. [. . . ]