User manual TOASTMASTER TECF1427
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual TOASTMASTER TECF1427. We hope that this TOASTMASTER TECF1427 user guide will be useful to you.
Manual abstract: user guide TOASTMASTER TECF1427
Detailed instructions for use are in the User's Guide.
[. . . ] COUNTERTOP FRYERS
COUNTERTOP FRYERS
MODELS 1427 & 1439 INSTALLATION - OPERATION - MAINTENANCE
Model TECF 1439
Model TECF 1427
Middleby Philippines Corporation ~ 113 Technology Ave. , Laguna Technopark Inc. , Binan, Laguna, Philippines 4024 Phone (632) 5208170 - Fax (632) 5208191 - www. middleby. com
MANUAL CF0105-1427-1439
COUNTERTOP FRYERS
Congratulations!You have purchased one of the finest pieces of heavy-duty commercial cooking equipment on the market. You will find that your new equipment, like all Toastmaster equipment, has been designed and manufactured to meet the toughest standards in the industry. Each piece of toastmaster equipment is carefully engineered and designs are verified through laboratory tests and field installations. [. . . ] Remove the jumper wire provided on the Auxiliary Circuit Terminal Block (AT1 to AT2). Use knockout located adjacent to the auxiliary circuit terminal block to connect 1/2" trade size conduit carrying two wires from the fire extinguishing system. Make connections according to Figure 2-2 or Figure 2-3, depending upon the following: (a. ) Follow Figure 2-2 if Switch `S' has the electrical ratings: 150VA, 1 Amp, 250 Volt for 208V or 240V rated fryer or 150VA, 1 Amp, 480 Volt for 480V rated fryer. Turn thermostat dial down to 250°F (121. 1 °C) or turn off during idle periods. As the shortening is being used, it is wearing out, consequently, the flash point (the temperature at which fire may result by overheating of the shortening) becomes lower. Replace old shortening with new when: · it begins bubbling excessively without food immersed, · it tastes of foreign flavors, or · gummy film collects on fry baskets. Swing-up element assembly contains all heating elements and temperature controls. Do not lift heating element assembly out of the shortening when the power switch is on Turn the thermostat dial to "OFF" before lifting the heating elements out of the shortening. The element assembly may be lifted and held out of the shortening by engaging the support bar against the stop pins. Refer to Figure 3-3.
CAUTION: Do not drop the heating elements into the fry pot. Shortening expansion is approximately 15% of capacity from room temperature to 400°F (204. 4°C).
14
Toastmaster ®
COUNTERTOP FRYERS
D. Preparation for Operation
SECTION 3 - OPERATION
1.
Choose a Shortening. The investment in good quality shortening will be rewarded with a long time use and fried foods of high standards. Shortening for frying should be bland in taste so it will not impart off flavors to foods. It is essential that the shortening selected have a high smoke point, well above the recommended frying temperatures. When the shortening reaches its smoking point, it begins to break down and becomes indigestible. Even with normal use, the composition of shortening changes and the smoking point becomes lower as it is used. Generally, hydrogenated fats, because of their high smoke point and resistance to break down, are considered ideal for deep frying. There are a number of reputable concerns packing shortening of this type who guarantee the smoke point of their product to be well above 400°F (204. 4°C).
2. 4.
Be sure the power ON/OFF switch and the thermostat dial are at the "OFF" position. WARNING: If solid shortening is used, pack tightly around heating elements. Turn power switch to ON and set thermostat dial to 250°F (121. 1 °C) until the elements are immersed in the melted shortening. [. . . ] The deep fryer will automatically shut down, which will also serve as a test of your high limit shut down. Turn thermostat dial back to "OFF", then brush off loose carbon and clean the shortening container. Keep all surfaces of the fry kettle free of splashed shortening or other foreign particles by washing with hot water and soap. This simple treatment not only keeps the fry kettle free of dirt and sparkling, but eliminates the danger of shortening accumulation forming hard to remove stains if left too long.
H. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE TOASTMASTER TECF1427
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual TOASTMASTER TECF1427 will begin.