User manual THOMSON SPEEDTOUCH 330

[. . . ] SpeedTouchTM USB/330 ADSL USB Modem Installation and User's Guide 300 SERIES SpeedTouchTM USB/330 Installation and User's Guide RFC1483 Bridged 3EC 36716 BAAA TCZZA Ed. 01 Status Change Note Short Title Copyright Released PeckelbeenS CD-UG STUSB/330 R2. 0 RFC en © 2002 THOMSON multimedia. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON multimedia. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON multimedia. [. . . ] In this section, the SpeedTouch Setup wizard (application) installation is fully described. In case you experience problems with this installation, you can try the Plug-and-Play compliant installation, shortly described at the end of this subsection. Windows OS differences The installation procedures might be slightly different depending on the Microsoft Windows OS you are using: · · · Some windows will look differently On Windows 98/98SE no 'Digital Signature' window will pop up For Windows 98/98SE, at the end of the installation procedure, you may be asked to enter an area code for Dial-up connections. 10 3EC 36716 BAAA TCZZA Ed. 01 3 SpeedTouchTM for Microsoft Windows Previous STUSB installations In case the STUSB was already installed on your system, the SpeedTouch Setup wizard (application) allows also an upgrade, removal or repair of the existing STUSB installation. The SpeedTouch Setup wizard (application) installation Step 1 Action Insert the STUSB Installation CD-rom in your PC's CD-rom drive. Note: In case the SpeedTouch Setup wizard (application) does not start automatically, open a 'Run' window via Start > Run from the Start menu and enter following path: D:\Setup. exe, where D stands for the drive letter of your CD-rom drive. The STUSB Setup program prepares the SpeedTouch Setup wizard (application): 2 As soon as the preparation is finished, the SpeedTouch Setup wizard (application) will start automatically. 3 The 'Welcome to SpeedTouchTM setup' window pops up: Click Next to proceed. 3EC 36716 BAAA TCZZA Ed. 01 11 3 SpeedTouchTM for Microsoft Windows Step 4 Action The 'Software License Agreement for SpeedTouchTM' window pops up: Click Yes to accept the terms of the agreement and to continue the installation. Note: ADSL must be available, as well as the appropriate central splitter or distributed filters. In most cases you only have to click Next to proceed with the installation procedure. At this point the SpeedTouch Setup wizard (application) will continue with the installation of the STUSB software and applications. The installation finishes with setting up STUSB's ADSL Wide Area Network (WAN) connectivity. Using the SpeedTouchTM" on page 16). 2 3 4 Installation results After you have correctly followed the STUSB installation procedures, the following folders and icons are added to your system: · · · SpeedTouch USB program folder: The SpeedTouch USB Diagnostics application is added. Desktop SpeedTouch Dial-up icon: A SpeedTouch Dial-up icon is added to your desktop. System tray SpeedTouch status icon: An STUSB status icon is added to the system tray, allowing instant status information of the STUSB. 3EC 36716 BAAA TCZZA Ed. Using the SpeedTouchTM STUSB status icon As soon your STUSB is installed, a STUSB status icon is shown at your desktop's system tray. The STUSB status icon is colored, depending on the state of the STUSB device. If you position your mouse pointer over the STUSB status icon, a message pops up: System tray icon Message ADSL Modem Modem not plugged in Description The STUSB is not plugged into the PC's USB port. The STUSB is plugged in, but has not (yet) accomplished synchronization over the ADSL line. The STUSB is connected, and synchronized, and has, up to this moment, sent X bytes, and received Y bytes over the ADSL line. STUSB status icon colors ADSL Modem Initializing ADSL line ADSL Modem. Sent : X bytes Received : Y bytes STUSB Diagnostics The STUSB status icon is also a short-cut to the STUSB Diagnostics application. This application allows you to overview some detailed parameters and settings of your STUSB and the current connection. [. . . ] Bridged PPPoE Connections PPPoE session client To use your SpeedTouchTM for Bridged PPPoE, you will need a PPPoE session client application, readily installed on your computer. This application will build connection icons for easy connectivity to your Service Provider. If your Service Provider requires you to use Bridged PPPoE, it should provide you with the PPPoE session client application. If they did not do so, contact your Service Provider for more information. [. . . ]