User manual THOMSON RR96L

[. . . ] The English version serves as the final reference on all product and operational details should any discrepancies arise in other languages. Safety Information TECHNICAL SPECIFICATIONS: Power supply AC 230V ~50Hz Clock backup:9V 6F22 Power consumption: 7W Please respect the environment. Before throwing any batteries away, consult your distributor who may be able to take them back for specific recycling. EN · Make sure that you keep your set away from water and high temperatures. · Do not use your system immediately after transporting it from a cold place to a warm place, as condensation may cause the system to malfunction. · Keep your unit away from humid areas and abnormally hot places. [. . . ] Normal operation will resume after AC power is restored so you will not have to reset the time or the alarm. Remove battery compartment door (located at the bottom of the radio) by applying thumb pressure to area indicated on battery door and then lift the door out and off the cabinet. Insert battery in the compartment and replace the compartment door. Power Failure Indicator When AC power is interrupted (disconnected) for a short period of time, both time and alarm settings will change (unless optional battery is installed). After AC power is restored (reconnected), the Digital Display will blink to indicate that power was interrupted and you should readjust the time and alarm settings. Note: Alkaline (NEDA 1604A / IEC 6LR61) battery is recommended. Carbon Zinc (NEDA 1604 / IEC 6F22) battery may be used but memory holding time will be substantially reduced. Memory holding time for a fresh alkaline battery is approximately 8 hours (if radio or alarm is not operated), which should take care of short, nuisance-type AC power failures. To preserve battery life, the radio should remain plugged into an AC outlet. Battery should be removed if the radio will be stored for more than one month. Leaky batteries may badly damage the clock radio. 2 Operating the radio EN Memory Set Recall 1 BA ND SET M AR cel AL n Ca R ew P NA IO NE TU E TIM RAD OFF ON Fw 2 d SLEEP ALAR M Tuning the Stations 1. Press ON/BAND to change the broadcast band (FM/MW for RR96M only, FM/ LW for RR96L), press OFF to turn off the radio. If you want to memorize this station, press MEMORY SET once, and press MEMORY RECALL to choose the station number you want to record in, once you choose a number, press MEMORY SET again to confirm. If you set the station in the AL location, it will be the wake up station of the alarm. To overwrite a presetted station, repeat step 3 and 4. Recalling the Stations 1. Press MEMORY RECALL to select the preset station (if available). Automatic station search 1. Press and hold or for 2 seconds, it will automatically search a station for you. Note: The unit can store up to 11 preset stations, "AL" refers to the Alarm Station. If no WAKE STATION is set, the wake up radio station will stay at your last listening radio station. 3 Operating the clock EN Memory Set Recall 1 BA ND SET P NA M A R cel AL n Ca R ew RAD IO NE TU E TIM OFF ON Fw 2 d SLEEP ALAR M Setting Clock Time Your digital clock operates on a 24-hour standard mechanism. When you press and hold REV or FWD, the time decrements or increments will follow by a faster rate. No adjustment can be made when LOCK mode is selected. Setting the Wake Time 1. Press the SET button once to set ALARM 1 (1 will flash on display), twice to set ALARM 2 (2 will flash on display). [. . . ] When the indicator is flashing, press REV or FWD to adjust nap time (from 10 minutes to 2 hours at an interval of 10 minutes. ) 3. Press NAP once to show time left. Stop the Nap alarm Press NAP or follow "Turning off Alarm". Note: Note 1. If the radio is currently on, then the radio will be on after NAP is pressed. 6 Other Functions Snooze Alarm Operation This operation allows extra sleep time after the alarm is on. The alarm will be off by pressing SNOOZE until the snooze period is over. [. . . ]