User manual THOMSON ROC2407 SUBCODES

[. . . ] Punch Through Controls Volume "Punch Through" Channel "Punch Through" Transport "Punch Through" B. to other Device Buttons Warranty and Specifications Glossary Appendix Assignment of Audio/Video Equipment Set Up Code Tables Audio Satellite TV VCR Cable CD DVD AUX 2 3 3 3 4 4 5 8 8 10 12 13 13 16 17 17 18 18 19 20 21 21 22 23 23 23 24 26 28 30 31 32 33 35 36 38 38 39 39 42 44 47 50 52 55 56 1 Introduction The Home Theater Master ROC2407 remote control is preprogrammed to operate over 1, 000 Audio and Video components so that you can set it up by simply punching in a three digit code number that matches your equipment. The ROC2407 also has the ability to learn new functions from your original remote controls, allowing you to customize the remote to your own needs and update it as you add new equipment. Please refer to page 8 - 18 for instructions on setting up the remote control. [. . . ] RETRY will appear in the LCD. 7 Press and hold the same button on the original remote, once again. The LCD on the ROC2407 will flash GOOD, the DEVICE Mode and then return to LEARN, verifying that the new function has been learned. 16 Using Your Remote 8 Press and hold the DEVICE button and the SEL/PLAY button simultaneously, once again. SAVED will flash three times in the LCD and return to the DEVICE mode, indicating that the programming has been stored. Erasing Learned Functions To erase learned functions, please refer to the following procedures: Erasing Individual Buttons: 1 Press the Device button for the mode where the learned function has been stored. 2 Press and hold the Device and the SEL/PLAY buttons simultaneously, for about 3 seconds, until the LCD shows LEARN. 3 Press and release the button to be erased. The LCD will flash ERASE, CLEAR, the Device Mode and then return to LEARN. Repeat Steps 3 and 4 for any other buttons to be erased. 5 To return to the normal operating mode, press the Device and the SEL/PLAY buttons simultaneously. The preprogrammed functions for these buttons will now operate on the remote control. 17 Using Your Remote Erasing All Buttons in One Device Mode: 1 Press the Device button for the mode to be erased. 2 Press and hold the Device and SEL/PLAY buttons simultaneously, for about 3 seconds, until the LCD shows LEARN. 3 Press and hold the Device and LIGHT buttons simultaneously for approximately five seconds and then release the buttons. The LCD will flash ERASE and then alternately CLEAR and the Device Mode. Note: When the LCD on the remote returns to the Device Mode, all the learned functions in the selected Device mode have been erased. All the buttons in that Device mode will now operate with the preprogrammed functions in that mode. Erasing All Buttons in All Device Modes 1 Press and hold the TV Device Button and the LIGHT button simultaneously, for approximately ten seconds. CLEAR will flash and INPUT will then appear in the LCD. 3 Press the ENTER button. The LCD will flash SAVE twice and return to AUDIO indicating that the join has been erased. Main Device Mode When the main device is displayed in the LCD, the ROC2407 will perform all of the preprogrammed, joined, learned and punch through features for that device mode. Automatic Audio Mode The remote is defaulted to the Automatic Audio. When the remote control is in this mode, pressing a Device button a second time will display A_XXX in the LCD indicating that the Volume and Mute controls of the device programmed into the Audio mode of the ROC2407 is active, while full function control of all other buttons of the current Device mode is maintained. Main Device Mode Automatic Audio Mode 21 Using Your Remote No IR commands are emitted during the second press of a Device button when the remote is in the Automatic Audio mode. Pressing the Device button again will return the remote to the Main Device Mode. To Delete the Automatic Audio for a Device mode: 1 Press and hold the AUDIO Device button and the LIGHT button simultaneously. A_SET will appear in the LCD. 2 Press the Device button corresponding to the Device mode to be deleted for Automatic Audio. A_OFF will appear in the LCD indicating the deleted status of the automatic Audio mode for the Device mode. 3 Press the ENTER button to store the programming. SAVE will flash in the LCD and then return to AUDIO. To Return to Automatic Audio for a Device mode: 1 Press and hold the AUDIO Device button and the LIGHT button simultaneously. A_SET will appear in the LCD. 2 Press the Device button corresponding to the Device mode to be added for Automatic Audio. A_ON will appear in the LCD indicating the active status of the Automatic Audio mode for the Device mode. 3 Press ENTER to store the programming. SAVE will flash in the LCD and then return to AUDIO. Backlighting All the buttons and the LCD on the ROC2407 are back-lit for 7 seconds when the LIGHT button is pressed. [. . . ] Each time the MENU button is pressed, the LCD will show one of twenty-seven displays. 3 Release the Device button when you find the new LCD display you wish to assign to the Device mode. AUD AUD CD CD DVD DVD AUX AUX SAT SAT TV TV VCR VCR CBL CBL POWER VOL MUTE MUTE T/ V T/ V CH GUIDE GUIDE PAUSE PAUSE MENU MENU R R E E W W SEL SEL PLAY PL AY PLAY F F . . CH CH Choice of LCD Displays TV DVD AMP2 PROJE AV VCR AUX TAPE1 AUX2 TAPE 1 2 CABLE 4 3 6 FAV SATFAV SLEEP SLEEP AUDIO TUNER SURR LIGHT CD AMP1 DAT DSS TV2 LD 5 8 0 VCR2 INFO INFO PRO. L PRO. L TAPE2 7 WEBTV 9 ENTER ENTER SHIFT SHIFT NEXT NEXT 3. CH 3. CH AUD2 +10 DAB 0 PIP PIP ALT ALT TEST TEST TUNER TUNER CD CD TAPE1 TAPE1 TAPE2 32 TAPE2 AUX AUX PHONO PHONO VCR1 VCR2/SAT LDP VCR1 VCR2/SAT LDP TV TV M1 M1 M2 M2 M3 M3 M4 M4 LIGHT LIGHT HOME THEATER MASTER LEARNING REMOTE CONTROL LEARNING REMOTE CONTROL Advanced Features LCD Displays in the Automatic Audio Mode A_TV A_DVD A_AM2 A_PRJ A_AV A_VCR A_AUX A_TAP1 A_AX2 A_TAP A_CAB A_TV2 A_TAP2 A_LD A_DAB A_SAT A_VC2 A_WEB A_A2 AUDIO A_TUN A_SUR A_LIT A_CD A_AM1 A_DAT A_DSS D: Programming a Second TV, VCR, etc. to Other Device Buttons. This feature is used to program the remote control for two or more TVs, VCRs, etc. , or to program a device into a mode with a different Device Button name. You can store the three-digit Set-Up Code number for any device into any other unused Device Button. [. . . ]