User manual THOMSON ROC 2407 CODE

[. . . ] Refer to the list provided with these instructions, page I of the codes. Hold down the SETUP (11) key until the red indicator lamp (1) remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). Press the product key (2) that corresponds to the type of product you want to control: TV: television set, DVD: DVD player, SAT: satellite receiver. [. . . ] Example: if you want to control a satellite receiver with the DVD key, begin by entering a satellite code (any satellite, for example: 603 for a Thomson satellite receiver) then begin the procedure. 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 * The coloured buttons can be used to select categories when teletext is activated, and specific functions depending on the make. 2 - Testing the remote control before you programme it 1. Turn on the product you want to control. 1 EN Checking the programming: Your product should be ready to receive remote control commands. Check to see that your remote functions correctly by performing the test described on page 3. Method B - 3-digit codes programming Before you start programming, you must find the code for the product to be controlled (television set, satellite receiver or DVD player). Refer to the list provided with these instructions, on page II of the codes. Hold down the SETUP (11) until the red indicator lamp (1) remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). Press the product key (2) that corresponds to the type of product you want to control: TV: television set, DVD: DVD player, SAT: satellite receiver. While the indicator is lit, enter the 3-digit code proposed for the product to be controlled (example: 036 for THOMSON). The red indicator then goes off if the code is correct or flashes, if the code is not on the list. Point the remote control towards the product and try to turn it off by pressing the POWER (12) key. Note: If you want to assign another type of product than those mentioned on the remote control, begin by entering a code that corresponds to the product you want to programme (a 3-digit code that you will find in the code booklet ­ see method B). Example: if you want to control a satellite receiver with the DVD key, begin by entering a satellite code (any satellite, for example: 603 for a Thomson satellite receiver) then begin the procedure. Method E - Programming for control of a COMBO TV/VCR, TV/DVD) Depending on the COMBO group (TV/VCR, VCR/DVD, etc. ) and the make, you will be required to enter a single code for both devices in the COMBO, or to enter two codes, one code per device. Before you start programming, you must find the subcode or code of the subset to be controlled (television or video recorder). Refer to the list supplied with this user manual (see page subcodes or codes). EN 2 1. Hold down the SETUP (11) key until the red indicator lamp (1) remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). Press the TV (2) key, then follow one of the programming methods (A, B, C or D) described earlier. If second code programming is required then repeat steps 2 and 3 above. 6 - Controlling volume in satellite and cable mode For satellite systems with a volume control, you can choose the product that the MUTE (15) and VOL (4) keys will control: the television volume or the volume of the satellite or cable receiver. Press the TV (2) key (the remote control must be in TV mode for this procedure). Hold down the SETUP (11) key until the red indicator lamp (1) remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. [. . . ] Press the number keys (0 to 9) in ascending order until the red indicator lamp (1) flashes once. The digit which made the red indicator lamp (1) flash, is the first number of the 3-digit code. When the third number is found, the red indicator lamp (1) goes off. 7 - The NAVILIGHT system The THOMSON NAVILIGHT navigation system allows you easy access to the settings of your television set (TV) or your video recorder (VCR) fitted with the THOMSON NAVILIGHT system provided that you have allocated the DVD or SAT keys to the video recorder. In the DVD position, make sure that the AV mode is activated for the TV set (the SCART socket must be selected). [. . . ]