User manual THOMSON GRUNDIG ESP2000

[. . . ] Setting Normal Time When power is on, the clock starts to enter the radio controlled clock mode. The LCD display (20) initially shows: - L: 0-5 receiving signal strength, 5 indicates signal level OK, 0-4 signal weak. - 00-59: a count of seconds - OFF: Alarm off mode - The receiving tower symbol starts to blink. [. . . ] Setting Alarm Time (Remark: please make sure the 'e' ONIOFF switch is in 'OFF' position to set alarm time or operate the alarm function) To set alarm time: Hold SET button(13) for two seconds to enter set mode, press SET button (1 3) twice to show the symbol and flash the alarm hour digits, then press UP (10) or DOWN (12) button to set alarm l hour. - Press MODE button (9) once to flash the alarm minute digits, then press UP (10) or DOWN (12) button to set alarm l minutes. - Press MODE button (9) once again to finish alarm l setting (all digits steady) or press SET button (13) to continue alarm2 time setting. To set alarm2 time: -Hold SET button (1 3) for two seconds to enter set mode, press SET button (13) three times to show the symbol and flash the alarm hour digits, then press UP (10) or DOWN (12) button to set alarm2 hour. -Press MODE button (9) once to flash the alarm minute digits, then press UP (10) or DOWN (12) button to set alarm2 minute. -Press MODE button (9) once again to finish alarm2 setting (all digits steady) or press SET button (13) to continue zone setting. Setting Alarm ON/OFF To turn alarm l ON: Press ALARM button (10) until the display shows both the alarm time and Press MODE button (9) until it returns to normal month and date display. To turn alarm l OFF: Press ALARM button (1 0) until the display shows both OFF and MODE button (9) until it returns to normal month and date display. symbol. symbol. Press To turn alarm2 ON: Press ALARM button (12) until the display shows both the alarm time and Press MODE button (9) until it returns to normal month and date display. To turn alarm2 OFF: Press ALARM button (12) until the display shows both OFF and MODE button (9) until it returns to normal month and date display. symbol. symbol. Press Wake to Radio: If the function slide switch (6) is set to RADIO position, the radio will come on automatically when the preset alarm time is reached. Wake to soothing sound: If the function slide switch (6) is set to SOUND, the soothing sound will come on automatically when the preset alarm time is reached. Wake to Alarm: If the function slide switch (6) is set to BEEP position, the alarm will come on for two minutes automatically when the preset alarm time is reached. Snooze: Press SNOOZE button (8) once within two minutes (or two minutes later, the alarm will stop automatically) to stop radio or alarm temporarily and give you extra eight minutes of sleep. Within this period, the symbol 'SNOOZE, shows on the LCD display (20). It will repeat if you press the SNOOZE button (8) again within two minutes. To stop the radio or alarm: To stop it, press any control button once except for SNOOZE button, or just wait for two minutes (the alarm will stop automatically). Selecting 5 Day Alarm / 7 Day Alarm Press 1-5 / 1-7 button (11) to select 1-5 or 1-7 alarm. 12/24 Hour Format Hold down the SNOOZE button (8) for five seconds to change from a 12 hour format to a 24 hour format. [. . . ] The success of time reception is not guaranteed; it is subject to environmental conditions and the distance from the signal source. Specifications POWER: Main Supply : AC 12OV/DC 6V Adapter 5OOmA (included) Battery Backup of Clock and Alarm DC 4. 5V (3 x "AA") (included) RADIO: AM 530 - 1710 kHz FM :88 - 108 MHz (Mono) RADIO CONTROLLED CLOCK: WWVB: 60 kHz FCC Statement It is possible, yet highly unlikely, that even your properly operating radio may cause interference to other radios or televisions. If the interference goes away after you turn off your radio, it is the cause. [. . . ]