User manual THOMSON DTI 1000

[. . . ] If you are not using the receiver for a long time (including overnight), please switch it off at the mains. Note that any software upgrades can take place at night at your request. There is a minimum of plastic parts and the packaging is largely made from recycled paper. It is also disassemblyfriendly allowing for easy recycling at the end of its life. CLEANING - Dust will collect on the unit and can be removed with dry clean cloth. [. . . ] To view channels that are not selected as favourites, use TV Guide, Service List or enter the channel number directly via the remote control, 0. . 9. Teletext and interactive services If your chosen channel has Teletext (MHEG) features use [TEXT] to access them. When the Timer Event has been activated, both RED and GREEN LEDs will be lit for the duration of the event. Please note that unless your VCR supports automatic scart recording YOU MUST ALSO SET THE VCR TIMER. In order to delete an entry you no longer need, position the cursor over the entry to be removed in the TIMER PROGRAMMING menu and press [RED]. Press [QUIT] again to confirm. 10 3569723D DTI1000 UM8. qxp 02/03/2005 12:24 Page 11 Use Parental controls You can use PARENTAL CONTROL to create viewing restrictions on your receiver. First create your own Personal Identification Number (PIN) as shown in the Advanced Setup section of this guide. The menu will appear. Censorship If the censorship level does not match the censorship rating of the program, access will be denied, the user is prompted for the PIN before access is granted. Press to set the censorship level to OFF, 6, 12, 15, 18 or BLOCK (for total block). Lock services From the PARENTAL CONTROL menu, select LOCK/UNLOCK SERVICES and press [OK]. To Lock/Unlock services scroll through the list of services with / and Lock/Unlock the highlighted service with [OK]. Once entered, all locked channels will be unlocked until the receiver is next in standby. Should any censored or locked channel be selected using the TIMER PROGRAMMING function, you must enter the PIN before the event is stored. Should any channel be censored or locked after the TIMER PROGRAMMING function has been set, you will be prompted for the PIN before access is granted. Entering an incorrect PIN will only allow the status of the channel to be displayed upon a blank screen. 11 3569723D DTI1000 UM8. qxp 02/03/2005 12:24 Page 12 Use Upgrading your Receiver From time to time new services are launched which may require your receiver to be upgraded with new software before you can use them. Sometimes new features may be introduced to enhance your receiver. Notification This menu is automatically displayed when a new "Over-AirDownload" is detected after switch on. Select DOWNLOAD LATER to set a timer event to receive the new software during the night. (However, the download may be re-detected and indicated the next time you switch on. ) It is highly recommended that you keep your receiver up to date. Check for download You can manually check to see if new software is available for download. The download can take up to 30 minutes or be slow to start, so please be patient. After the download, details about the new software will be displayed for you. There may also be a telephone number to call in case of any difficulty. If the download fails, try again later. During part of the download, DO NOT switch off the receiver, this warning is displayed on screen. 12 3569723D DTI1000 UM8. qxp 02/03/2005 12:24 Page 13 Use Other information Technical information details The technical information screen displays the hardware and software information of the receiver. This information may be required by the service agent or service call operator. Select TECHNICAL INFORMATION and press [OK]. Hotel Mode When power to the receiver is disconnected, the unit will always return to standby when next reconnected. [. . . ] Damage caused by accidents including, but not limited to, lightning, fire, water; 2. Transport costs between the home and place of service and other costs and risks of transport relating directly or indirectly to this guarantee; 3. Damage to the product resulting from neglect, misuse, including but not limited to, failure to use, repair and/or install the product for its normal domestic purposes and/or in accordance with the operating instructions on its proper installation and use; 4. Modifications, adaptations and alterations of the product to operate in a country other than that for which it was originally designed and manufactured, or any damage resulting from such modifications; These statements do not affect your statutory rights as a consumer under applicable national legislation in force, nor your consumer's rights against the dealer from whom you bought the product. [. . . ]