User manual THOMSON CS500

[. . . ] u s e r m a n VOLUME DEMO TUNE/PRESET ON/ECO SOURCE u DISC SKIP DISC OPEN/CLOSE CD-R / RW COMPATIBLE a 5 DISC CHANGER l THOMSON 46, quai Alphonse Le Gallo 92648 Boulogne Cedex FRANCE 55806290 www. thomson. net CS500 Safety Information EN Thomson Information CAUTION!This system must be opened only by qualified technicians to prevent accidents caused by the laser beam. LASER = 780 nm, P max = 5 mW Rating Information: At bottom/rear of the unit. This unit comply with the existing requirements In accordance with the rating plate of the unit, this unit complies with current standards concerning electrical safety and electromagnetic compatibility. [. . . ] · Playback capability for CD-RW discs may vary due to variations in the quality of the CD-RW disc and the recorder used to create the disc. Setting the Timer 1. Press and hold TIMER until the ON and clock hour flashes on the display ( ON - timer on time ). For setting time, press SKIP BACKWARD or SKIP FORWARD on the main unit or PRESET or PRESET on the remote control to set the hour and then press TIMER to shift to minute digits. Press SKIP BACKWARD or SKIP FORWARD on the main unit or PRESET or PRESET on the remote control to set the minute. Press TIMER to change to OF (timer off time) with clock time flashing. Repeat steps 2 & 3 for timer off time setting. Play and Pause Discs · Press PLAY/PAUSE in stop mode to begin playback. · Press PLAY/PAUSE during playback to to pause disc. Press again to resume. Note: Be sure to remove all discs from the disc compartment before moving or transporting the unit! Play and load simultaneously by: 1. Press DISC OPEN/CLOSE on the front panel of the main unit or OPEN/CLOSE on the remote control to open the tray while a CD is playing. Press DISC OPEN/CLOSE on the front panel of the main unit or OPEN/CLOSE on the remote control to close the tray. 6 7 CD Player EN Selecting a Disc · Press DISC 1, DISC 2, DISC 3, DISC 4, or DISC 5 on the main unit to directly access the corresponding disc. Press the corresponding disc number on the main unit or DISC SKIP to select disc. Press SKIP BACKWARD / SKIP FORWARD on the main unit or TUNING or on the remote control to select track to enter into memory. Repeat steps 2 to 4 to store more tracks into program memory. Radio Selecting Tuner Band 1. Press SOURCE on the main unit or TUNER on the remote control to enter Tuner mode. Press CD INFO/BAND to select Radio band. Auto Preset Programming Press and hold CD INFO/BAND button for 2 seconds to scan stations in FM band. Beware of your preset channels being erased accidentally because the scanning and storing process is automatic upon pressing the button. You can stop the automatic scan by pressing any button, but the erased stations cannot be recovered. EN Tip: Your audio system has 32 preset stations. Searching Through a CD · Press SKIP BACKWARD / SKIP FORWARD on the main unit or or on the remote control to skip to the previous or next track. · Press and hold SKIP BACKWARD / SKIP FORWARD on the main unit or or on the remote control to search through a CD while it is playing. Playing a Program List While in PROGRAM mode , press PLAY/PAUSE . If you are not currently in program mode, press PROG/SET to enter program mode before pressing PLAY/PAUSE . Tuning to a Station Press SKIP BACKWARD / SKIP FORWARD on the main unit or TUNING or on the remote control to select frequency. Manually Setting Presets 1. The most recently accessed program location will flash on the display. If a different program location is preferred, press SKIP BACKWARD or SKIP FORWARD on the main unit or PRESET or on the remote control to move to the desired preset number (1-32). Press PROG/SET to store the selected frequency at that preset. Using Presets The tuner can be in either TUNE or PRESET mode. When in preset mode, · Press TUNE/PRESET on the main system or PRESET or on the remote control to access the previous or next preset station. [. . . ] If you notice some slack in the tape, use a pencil to tighten it up before you insert it. Poor radio reception Side A Protection A Side B Protection B CD Lens Care When your CD lens gets dirty it can also cause the system to output poor sound quality. To clean the lens you will need to purchase a CD lens cleaner which can maintain the output sound quality of your system. For instructions on cleaning the CD lens, refer to the ones accompanying the lens cleaner. CD does not · Check that CD is in the tray. · Make sure the speakers are at least 3 feet away or on a different surface from the main unit. "ERROR" message · Unplug the unit · See if there is anything obstructing the CD door or preventing it from closing. A Tape does not play · Unplug the power cord and plug it back in again. 12 13 Important Information EN Safety Precautions · Never open the cabinet under any circumstances. [. . . ]