User manual THOMSON 5570MC

[. . . ] Remove the power plug from the wall outlet under the following conditions : 1. During a thunderstorm, it is also recommended that you disconnect the aerial plug. Additional information : Your TV set is adequately shielded to prevent emission of X-rays. Work by non-qualified technicians, modification of the high voltage setting or the replacement of the tube with a model that does not comply with the manufacturer's specifications may lead to X-radiation. [. . . ] Press briefly to clear the menu from the screen. NEW CHANNELS TV If a channel is not found or a new channel starts to broadcast in your region please refer to MANUAL CHANNEL SETTING. -7- NEW REGION (If you move to another region, or you want to start again for any other reason) Start the automatic search again and reorganise the programmes. To do this, call up the INSTALLATION menu and proceed as described earlier (page 6). All programmes and names previously stored are then erased. TV Press briefly to clear the menu from the screen. RE-ORGANIZING PROGRAMMES If you subsequenttly wish to re-organize the order of your programmes please proceed as follows : MENU Press briefly to call up the main menu. Press briefly and the PROGRAMME ORGANIZER menu is displayed. MENU MENU PREF. Organis. + FUNCT VT While the television is in any AV mode, (audio-visual), PROGRAMME ORGANIZER menu cannot be displayed. PR -- PR + Select the programme. To erase : PROGRAMME ORGANIZER PR 01 CH22 PR -- / PR + + -- STOP VT keep pressed for some seconds until the station disappears. To store : To select a station To give a prog. To erase this station When completed : press [ TV ] FUNCT VT press briefly and a new menu will appear. Press repeatedly to select the Store line. PROGRAMME ORGANIZER PR 01 CH22 STOP VT FUNCT VT Program No : -- -- Name : -- -- -- -- To store and continue MENU FUNCT VT Press briefly to store your changes in memory, the + turns to OK. Repeat the above procedure to change other programmes. TV Press briefly to clear the menu from the screen. -8- PICTURE ADJUSTMENTS MENU FUNCT VT MENU Press briefly to call up the main menu. Press the button repeatedly to select the function you want to adjust : = BRIGHTNESS = COLOUR = CONTRAST = SHARPNESS MENU + = TINT PREF. The tint adjustment is active only in NTSC mode. STOP VT FUNCT VT To carry out the adjustments. The Stand-By light becomes brighter. TV PR -- PR + Note : The television will automatically switch to Stand-By after a few minutes if there is no signal on the channel being watched. - 10 - OTHER FUNCTIONS MENU SETTING THE CLOCK MENU Press briefly to call up the main menu. Organis. + Press briefly to select the -- -- : -- -- line. FUNCT VT Press briefly. The Time Set menu is displayed. The STOP VT line is selected. ----:---- ----:---- Press -- repeatedly to adjust the hours. Press + repeatedly to adjust the minutes. -- + FUNCT VT TV Press briefly to clear the menu from the screen. You can reset the clock as above or select the time reference programme. S TA N D - B Y ( S L E E P T I M E R ) Press briefly. The menu shown on the right is displayed. ----:---- ----:---- On Off Program. : 01 -- + The line is selected. STOP VT Stand-By times of between 15 minutes and 4 hours can be set (in 15-minute steps). The time left before Stand-By can be checked at any time: Press briefly. The time left is displayed for a few seconds. FUNCT VT Press repeatedly to adjust the minutes (from 0 to 45 minutes in 15-minute steps). TV TV 00 : 13 STOP VT The television will switch to Stand-By at the end of the timer interval. The Stand-By light flashes to indicate that the CHILD LOCK function has been activated. The set can only be switched on again using the remote control not by the keyboard. --+ ----:---- Press repeatedly to go back to -- -- : -- --. Press briefly to clear the menu from the screen. - 11 - TV ALARM This cannot be used if the clock is not set. You can programme your television set to switch on automatically to a chosen programme at a chosen time. [. . . ] In the case of an S-VHS or Hi-8 device, select S-VIDEO On in the Picture menu (p. To use the connected device : / Press to select the audio-visual programme. AV1 is displayed at the bottom of the screen, (audio-visual display). When the VCR is stopped and if you have not changed channel during play, the TV set returns to the station previously watched. If the television has been switched on by the video recorder, it will be placed on standby when the video recorder is switched off. [. . . ]