User manual STRONG PRIMASAT II

[. . . ] PART 1 • English Table of Contents 1. 0 Introduction 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Accessories 1. 5 Usage of external USB devices 2. 0 Your Receiver 2. 1 Front Panel 2. 2 Rear Panel 2. 3 Remote Control Unit 2. 4 Default PIN code: 0000 2. 5 Installing the Batteries 2. 6 Using the Remote Control 3. 0 Connections 3. 1 Basic connection with SCART cable 3. 2 Connecting to Satellite Dish 3. 3 Connecting to a Digital Audio Amplifier 3. 4 Connecting to USB device 4. 0 First time installation 4. 1 OSD Settings 4. 2 My Dish 5. 0 Main Menu 5. 1 TV 5. 2 Radio 5. 3 Accessory 5. 4 Configuration 6. 0 Changing channel list mode 7. 0 Audio Language Selection 8. 0 Teletext 9. 0 Subtitles 10. 0 Trouble Shooting 11. 0 Specifications 2 2 2 3 3 3 3 3 3 4 4 4 5 5 5 5 5 5 5 5 6 7 8 9 9 10 13 13 13 13 14 15 02 Jul 2013 15:38 STRONG declares that this item complies with the basic requirements and other relevant regulations of directives CE 2004/108/EC and 73/23EC; RoHS 2002/95/EC Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change. All product names are trademarks or registered trademarks of their respective owners. All rights reserved. 1 English PART 1 • English 1. 0 Introduction 1. 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots. [. . . ] Once the dish is adjusted to the desired position, select the OK field and press OK to save. (For Astra 19, 2E after a scan, the list starts with a pre-installed list, followed with new found channels. ) You can save 32 satellite positions. Then press pq to select the desired channel and press OK to lock this channel. (Press YELLOW button to save. ) NOTE:  This only works if Channel Lock is switched ON in the Pin Code menu from the Configuration menuDefault Pin Code is “0000”. 5. 1. 1. 3 Edit Press tu to select , then press pq to select the desired channel and OK to edit this channel. (Press YELLOW button to save. ) 5. 1. 1. 4 Move Press tu to select , then press pq to select the desired channel and OK to move this channel. Use pq to move the channel to its new location and press OK to confirm. (Press YELLOW button to save all your changes. ) 5. 1. 1. 5 Sort Press tu to select . You can sort channels by Name A~Z, Name Z~A with the RED button or Pay-Free or Free- Pay with the GREEN button. NOTE:  Please take care once desired order is executed this order stays. 5. 1. 1. 6 Skip Press tu to select , then press pq to select the desired channel and OK to skip this channel. (Press YELLOW button to save. ) 8 PART 1 • English 5. 1. 1. 7 Delete Press tu to select , then press pq to select the desired channel and OK to delete this channel. Press the YELLOW button to save and confirm or exit the pop up screen. 5. 1. 1. 8 Search Press tu to select , then press OK and use the On Screen Display menu to search for a programme. English 9 5. 1. 2 EPG (Electronic Programme Guide) The EPG shows the programme schedule for all services broadcasting EPG information. Press pq to select the desired channel and the right screen will show you the available EPG. Press u to step in to the EPG schedule for the current channel and use pq for EPG± and tu to change Date. 5. 1. 3 Programming Timer from EPG Book the selected programme in EPG screen with the RED button. A Timer Settings menu will pop up and you can edit this menu with pq tu and the numeric buttons to set the timer details. The receiver will switch on to the right programme at the right time. 5. 2 Radio Press MENU to move to Main Menu, then press tu to move to Radio and press OK to enter the Radio Channels menu. Use tu to move to the following sub-menus Fav, Lock, Edit, Move, Sort, Skip, Delete and Search. NOTE:  each function, refer to chapters 5. 1. 1. 1 to 5. 1. 1. 8 as the functions are identical. [. . . ] (Read chapter 5. 4. 6. 2) Warning!  NEVER disconnect the USB device from the receiver, the receiver from the main or switch the power OFF during the update/backup procedure. As soon as the update has been finished, the receiver restarts automatically!English 13 6. 0 Changing channel list mode To change between TV and Radio channel lists use TV/RADIO in normal viewing mode. To change channel list to Favourite in normal viewing mode, press FAV. [. . . ]