User manual STONERIDGE ELECTRONICS SE5000

[. . . ] UK Stoneridge Electronics Digital Tachograph SE5000 User Manual USER MANUAL 9000-101534_01R01 USER_MANUAL_ENGLISH Part Number 6800-900 Page 1 Copyright © 2005 Stoneridge Electronics AB Manufacturers of VEEDER-ROOT Tachographs UK IMPORTANT INFORMATION Due to driver and road safety requirements, it is strongly advised that driver interaction with a Digital Tachograph Vehicle Unit (VU) is not carried out whilst a vehicle is in motion (Note: the term `VU' will be used to describe a Digital Tachograph from this point forward). If a driver does not have a valid VU driver smartcard they must not drive a vehicle fitted with the VU described in this manual as it is against EU law. If a card is lost, stolen or faulty, a temporary exemption to drive without a card may be granted by the national enforcement agency of the country in which driving is to be done. Drivers should contact national enforcement agencies directly (as indicated in Appendix 7 - National Enforcement Agencies) for clarification on this matter - drivers are responsible for ensuring that they obey driving laws. [. . . ] Press the `enter' button again to enter the "Print/Display" sub-menu and use the `up' or `down' buttons to scroll through the list of six printout types (as described in the section 5. 1 Types of Printout) until the required option is displayed on the bottom line. Press the `enter' button once more to select the displayed `print/display' option. If the wrong sub-menu is entered, press the `cancel' button to go to the previous menu. / Print menu Once a printout has been initiated, it can only be stopped by long-pressing the `cancel' button. A warning message will be displayed as shown to indicate that printing has been cancelled. It should be noted that if there is a problem with the printer then a warning message will be displayed, with the exact message displayed dependant on the problem. A full list of printing instructions for each printout type and a description of printer warning messages is included in Appendix 4 - Details of Printing Routines. 5. 3 Sample Printout Printing cancelled A sample `Daily Driver Activities From Card' printout is shown below in Figure 8. The printout initially consists of information on the cardholder and then information on the VU and the vehicle in which it was inserted. Then shown are details of the driver duties for the day and start and end odometer information. Date & time of printout 20. 07. 2004 09:48 (UTC) ----------------------24h ---------------------- Andersson Richard S /ABCD6789012345 1 1 31. 12. 2037 USER MANUAL 9000-101534_01R01 USER_MANUAL_ENGLISH Part Number 6800-900 Type of print out - Daily Driver Activities from card Cardholder's last name Cardholder's first name Page 29 Copyright © 2005 Stoneridge Electronics AB Manufacturers of VEEDER-ROOT Tachographs UK Card issuing state & number ---------------------- 1234567890ABCDEFG VIN S /123 A 23F ---------------------- Stoneridge Electronics SE5000 1 56789123 ---------------------- Johansson and Sons S /WSABC479328652 1 1 15. 01. 2004 ----------------------19. 07. 2004 10 -----------------------?18:26 23:59 05h34 -----------1----------- S /123 A 23F 97 206 km 08:04 11:00 02h57 11:00 14:39 03h40 * 14:39 15:32 00h54 15:32 15:53 00h54 15:53 17:10 01h18 * 17:10 17:15 00h06 17:15 17:29 00h15 17:29 17:33 00h05 97 716 km 510 km USER MANUAL 9000-101534_01R01 USER_MANUAL_ENGLISH Part Number 6800-900 Card expiry date. Vehicle registration state & number VU Manufacturer VU Part Number Workshop carrying out last calibration Workshop card number Date of last calibration Date of Driver Activities, daily counter Period of unknown activity Period of activity entered manually Period of unknown activity Card inserted into slot 1 Vehicle Card was inserted into Vehicle odometer value at card insertion Activities whilst card was inserted = Rest (Note: rest periods of more that 1 hour are identified with `*') = Available = Work Page 30 Copyright © 2005 Stoneridge Electronics AB Manufacturers of VEEDER-ROOT Tachographs UK = Drive Vehicle odometer value at card removal, distance travelled Figure 8 Sample Printout 6 Settings Menu The settings menu is used for setting the VU clock (adjustment of UTC and setting local time), to invert the display or to carry out VU internal tests. The Settings menu can be accessed from any of the `Driving' display screens (see Appendix 5 - Display Screens Selectable Whilst Driving for details). Initially press the `enter' button to access the `Main Menu'. The `up' or `down' buttons should be pressed to scroll through the main menu functions until the Settings submenu screen is displayed as shown. Press the `enter' button again to access the Settings submenu and press the `up' or `down' buttons to scroll through the list of settings options as follows: Settings menu · · · · " Settings Local Time" - this is used to adjust the VU local offset time. " Settings Invert display" - this is used to invert the VU display. " Settings Built-in test" - this is used to check the functionality of the different parts of a VU. Once the required settings option is displayed on the bottom line, press the `enter' button once more to select the required displayed `settings' option. If the wrong sub-menu is entered, press the `cancel' button to go to the previous menu. 6. 1 UTC Time and Local Time All VUs use Universal Time Coordinated (UTC) as their master reference time. UTC is an incremental count of the number of elapsed st seconds since 1 January 1970, and is approximately equivalent to Greenwich Mean Time. A local time may also be shown on the VU and this can be adjusted in ±30 minute offsets up to a maximum of ±12 hours from the UTC time. It should be noted that all driving event times stored are UTC times - setting a local time on the VU is for display purposes only. USER MANUAL 9000-101534_01R01 USER_MANUAL_ENGLISH Part Number 6800-900 Page 31 Copyright © 2005 Stoneridge Electronics AB Manufacturers of VEEDER-ROOT Tachographs UK 6. 1. 1 Adjusting VU UTC Time A user can alter the VU UTC time by a magnitude of ±1 minute per week. It should be noted that a Tachograph Workshop can alter the VUs' UTC time by any amount. [. . . ] dark becomes light / light becomes dark) for 2 seconds before returning to the original display. Selecting this test will result in a default printout being emitted from the VU. If this test is selected the user will be prompted to press all of the buttons in turn from left to right - each button press must be done within 2 seconds or the test will automatically fail. Action to be Taken On Test Failure If the display is unreadable the vehicle must be returned to a Tachograph Workshop for VU investigation. [. . . ]