User manual SONY VPH-1001Q

[. . . ] This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] User1, User2, User3: You can adjust the quality of the picture to suit your taste and then store the settings. Once the settings are stored, you can view the picture with the adjusted picture quality by pressing the PICTURE MODE button on the remote control. Tips · You can also adjust the picture quality in "Dynamic", "Standard" or "Cinema", and store the settings. To reset everything to the factory settings, select "Reset" from the menu. · Some adjustment windows cannot be displayed, depending on the type of input signal. For details, see "Input Signals and Adjustable/Setting Items" (1 page 67). 40 Cinema Black Pro Advanced Iris Switches the iris function during projection. Auto1: Automatically switches to an optimum iris according to a projected scene. Auto2: An optimum iris becomes smaller than when set to "Auto1". Sensitivity: If "Auto1" or "Auto2" is selected, either "Recommend", "Fast", or "Slow" can be selected according to the desired response speed with Sensitivity Mode. Tip When you switch from "Low" to "High", the number of turns of the fan increases, and the fan noise becomes slightly louder. You can make adjustments by pressing the CONTRAST+/­ on the remote control. Zoom: A normal 16:9 aspect ratio picture is enlarged vertically and horizontally in the same ratio to fill the screen. Anamorphic Zoom: A 2. 35:1 aspect ratio picture is converted to a normal 16:9 picture on the screen. This mode is best suited when using a commercially available Anamorphic lens which converts a normal 16:9 aspect ratio picture to a 2. 35:1 picture. You can set the aspect ratio of the picture to be displayed for the current input signal. Full1: Displays a picture on the whole of the screen without changing the aspect ratio of the original picture. Zoom: A normal 16:9 aspect ratio picture is enlarged vertically and horizontally in the same ratio to fill the screen. Tip To display the displayable region within the four directions of the screen, refer to "Blanking" on the Installation menu (1 page 51). Wide Mode (PC signal) Over Scan 44 Screen Area Selects the size of the picture when a Hi-Vision picture is overscanned. Through: Does not expands the picture on the whole of the screen. Note This item is effective only when a Hi-Vision signal (preset memory No. 7, 8, 9, 12, 13 and 14) is input and "On" is selected in "Over Scan". V Center Adjust the whole picture by moving up and down on the screen. As the selected number increases, the screen moves up, and as the selected number decreases, the screen moves down. Note Using the Menus This item is adjustable only when "Zoom" is selected. [. . . ] 11 kg (24 lb 4 oz) Power requirements AC 100 to 240 V, 1. 3 to 3. 0 A, 50/60 Hz Power consumption Max. 300 W Standby mode: 8 W Standby mode (low): 0. 5 W Operating temperature 5°C to 35°C (41°F to 95°F) Operating humidity 35% to 85% (no condensation) Storage temperature ­20°C to +60°C (­4°F to +140°F) Storage humidity 10% to 90% Input Video input VIDEO: phono type Composite video: 1 Vp-p±2 dB sync negative (75 ohms terminated) S VIDEO: Y/C mini DIN 4-pin type Y (luminance): 1 Vp-p±2 dB sync negative (75 ohms terminated) C (chrominance): burst 0. 286 Vpp ±2 dB (NTSC) (75 ohms terminated), or burst 0. 3 Vp-p±2 dB (PAL) (75 ohms terminated) Y PB/CB PR/CR Component: phono type Y with Sync: 1 Vp-p±2dB sync negative (75 ohms terminated) 62 Supplied accessories Remote control RM-PJVW60 (1) Size AA (R6) batteries (2) AC power cord (1) Lens Cap (1) Operating Instructions (1) CD-ROM (ImageDirector3) (1) Design and specifications are subject to change without notice. Optional accessories Projector Lamp LMP-H200 (for replacement) Projector Suspension Support PSS-H10 Others 63 Warning on power connection Use a proper power cord for your local power supply. The United States, Continental Canada Europe Plug type Female end Cord type Rated Voltage & Current YP-3 YC-13 SVT 10A/125V YP-12A YC-13D H05VV-F 10A/250V VDE UK, Ireland, Australia, New Zealand * VM0303B CEE (13) 53 rd (OC) 10A/250V VDE Japan China YP-359 YC-13 VCTF VM0722 VM0724 227 IEC 53(RVV) 12A/125V 10A/250V DENANHO CCC Safety approval UL/CSA * Use a rated plug that complies with the regulation of each country/region and the specifications. Preset Signals The following table shows the signals and video formats which you can project using this unit. When a signal other than the preset signal shown below is input, the picture may not be displayed properly. Memory No. 1 2 3 4 5 Preset signal (resolution) VIDEO/60 VIDEO/50 480/60i 576/50i 480/60p 60 Hz 50 Hz DTV 480/60i (720 × 480i) DTV 576/50i (720 × 576i) 480/60p (720 × 480p) (Progressive NTSC) 576/50p (720 × 576p) (Progressive PAL) 1035/60i (1920 × 1035i), 1080/60i (1920 × 1080i) 1080/50i (1920 × 1080i) fH (kHz) 15. 734 15. 625 15. 734 15. 625 31. 470 fV (Hz) 59. 940 50. 000 59. 940 50. 000 60. 000 ­ ­ SonG/Y or composite sync SonG/Y or composite sync/composite video SonG/Y Sync H Size ­ ­ ­ ­ ­ 6 576/50p 31. 250 50. 000 SonG/Y ­ 7 1080/60i 33. 750 60. 000 SonG/Y ­ 8 1080/50i 28. 130 50. 000 SonG/Y ­ 64 Memory No. [. . . ]