User manual SONY VPH-1000Q

[. . . ] 15(GB) Notes on Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18(GB) Modifying Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20(GB) Removing the Upper Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20(GB) Changing the Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When the picture is being projected using this type of sync signal, the POS (NEG) is displayed in green. When the picture is being projected without using this type of sync signal, the POS (NEG) is displayed in white. ­ ­ ­: No sync signal is input. 50 (GB) Before adjustment V (Vertical)-SYNC Indicates the polarity of the vertical or composite sync signal. When the picture is being projected using this type of sync signal, the POS (NEG) is displayed in green. When the picture is being projected without using this type of sync signal, the POS (NEG) is displayed in white. ­ ­ ­: No sync signal is input. INPUT MEMORY No. The upper number is the memory number of the data automatically loaded when the current signal is input. The lower number is the new memory number in which the adjustment data of the current input signal is stored. The existent memory number is displayed in green, and a new memory number in yellow. For details, see "Memory structure" on page 96 (GB). By default seven basic data are stored in the following memory numbers. Memory number 00 01 02 03 04 05 06 Preset signal frequencies fH fV 15. 7 kHz 24. 8 kHz 31. 5 kHz 48. 3 kHz 64. 0 kHz 31. 5 kHz 33. 8 kHz 60 Hz 56 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz Types of the input signal Video (NTSC3. 58) RGB Before adjustment SonG (Sync on Green) Indicates the polarity of the sync on Green. When the picture is being projected using this type of sync signal, the NEG is displayed in green. When the picture is being projected without using this type of sync signal, the NEG is displayed in white. ­ ­ ­: No sync signal is input. RGB RGB RGB IDTV (NTSC3. 58) HDTV (Y/PB/PR) INPUT SIGNAL FREQUENCY SENSITIVITY Displays the type of current input signal. (version) ALL WHITE MODE Sets the duration of all white mode during a warm-up period. Indicates the ROM version (M, S1, S2 and S3) used for the projector. TIMER Indicates the use time of the projector and that of each CRT. ALL WHITE MODE:20mln OPERATION TIMER 00001HRS CRT TIMER: R:0001HRS G:0001HRS B:0001HRS RESET: RESET Use the V, v, B or b key to set the duration in 1 minute increments from 0 to 99 minutes. To set the projector to display the picture immediately after the projector is turned on, set the duration to "0 min. " For details, see "Changing the Initialization Period" on page 103 (GB). SEL: SET: ENTER EXIT: MENU OPERATION TIMER: Indicates the total use time of the projector. CRT TIMER: Indicates the use time of the red, green and blue CRTs, respectively. Before adjustment 53 (GB) Using the MENU The ABL (Automatic Brightness Limiter) LINK Menu The ABL LINK menu is used for adjusting to make the brightness of the multi-screen uniform when connecting multiple projectors. S SERVICE SETTING SET INFO. ABL LINK ABL LEVEL ADJ (adjust) When ABL LINK is set to ON, adjust the brightness of each projector so that the brightness of all projectors looks the same. INPUT-A ABL LINK:ON SUB CONTRAST: 0 ABL LEVEL ADJ: 0 ABL LEVEL ADJ: 0 SEL: SET: ENTER EXIT: MENU Before adjustment For details, see "Using the Linked ABL Function" on page 31 (GB). ABL LINK When set to ON, the ABL (Automatic Brightness Limiter; to control the brightness of the picture when it is too high) functions on all projectors once the ABL functions on any projector. S SERVICE SETTING SET INFO. ABL LINK UT-A ABL LINK: SUB CONTR ABL LEVEL ON OFF SEL: SET: ENTER EXIT: MENU SUB CONTRAST When ABL LINK is set to ON, adjust the brightness of each projector so that the brightness of all projectors looks the same. SUB CONTRAST: 0 54 (GB) Before adjustment The OPTION Menu The density and sharpness in the vertical direction of the input signal can be adjusted. INPUT-A OPTION INT IDTV SEL: SET: ENTER EXIT: MENU INT. (internal) IDTV Before adjustment Set to ON to project the video, S video, component or RGB (15 kHz) signal at double density. INT IDTV INT. IDTV: V APERTUR ON OFF SEL: SET: ENTER EXIT: MENU V. (vertical) APERTURE Corrects the sharpness in the vertical direction. You can set the sharpness to the LOW, MID (middle) or HIGH level. INT IDTV INT. IDTV:OFF V APERTURE: LOW MID HIGH SEL: SET: ENTER EXIT: MENU Before adjustment 55 (GB) Test Patterns Test Patterns In each adjustment mode, an appropriate test pattern appears. In addition, you can display other test patterns by pressing the PATTERN key. 1 CROSS HAIR 2 HATCH (9 x 9) 3 HATCH (17 x 17) 4 DOT (9 x 9) 5H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H 6 H INV (inverse) H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H 7 ME 8 ME INV (inverse) Before adjustment 9 ALL WHITE 0 WINDOW !¡ WINDOW&LINE !TM COLOR BAR !£ HACHT INV (invert) (17 x 17) (for adjusting registration only) !¢ Sub-pattern 1 (subsidiary adjustment pattern 1) (for adjusting SIZE, LIN, SKEW and BOW only) !Sub-pattern 2 (subsidiary adjustment pattern 2) (for adjusting KEY and PIN only) !§ CROSS (9 x 9) (for adjusting ZONE only) 56 (GB) Before adjustment !¶ PLUGE (for adjusting BIAS only) !· Stair step (for adjusting GAIN only) !ª 5 IRE (for adjusting BIAS only) @º 100 IRE (for adjusting GAIN and BIAS only) The patterns 1 to !TM appear in numerical order when pressing the PATTERN key in service adjustment mode. [. . . ] Service data reset Resets to the data saved in the service data block. 128 data reset (ZONE only) Resets the ZONE adjustment data to 128. User data block Load Save Factory data block Factory data reset Service data block Service data reset Normal adjustment data block 128 data 128 data reset (ZONE only) Adjustments Adjustments 99 (GB) Resetting the Data Fine Adjustment for Each Input Signal Resetting the data 1 2 Select the adjustment mode to be reset. (Example: To reset the red registration data to the factory preset data) REGISTRATION RED DATA RESET MODE Service Data Factory Data SEL: SET: ENTER EXIT: NORMAL 3 Press the V or v key to select the reset mode, then press the ENTER key. To cancel reset mode, press the NORMAL key. RESET complete! Adjustments All red registration adjustment data will be reset to the factory preset data. 100 (GB) Adjustments Protecting the Setting When you turn off the projector with the remote control, the adjustment keys become inoperable in order to prevent users from accidentally changing the adjustments (user mode). [. . . ]