User manual SONY VAIO VGN-NW220F/W

[. . . ] This document contains proprietary information that is protected by copyright. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of HP. Box 4010 Cupertino, CA 95015-4010 USA Copyright © 2004­2005 Hewlett-Packard Development Company, L. P. registered marks of the United States Environmental Protection Agency. [. . . ] Insert the green plug on the end of the right speaker audio cable 3 into the computer audio line out connector. User's Guide 3­17 Setting Up the Monitor 3. If you are using an HP subwoofer, insert the subwoofer audio plug into the right speaker subwoofer connector -. Connect one end of the speaker DC power cable w to the right speaker DC power connector q. Connect the other end of the cable to the DC power connector 4 on the f monitor. As needed, connect headphones to the headphone jack connector (not shown) on the right speaker. SERIAL ETHERNET TV-OUT VID/AUD S-VID IN LINE IN IR FM TV 3 8 4 12 9 10 11 Connecting the f monitor speakers 3­18 User's Guide Setting Up the Monitor Item 3 4 Description Speaker audio cable at computer connector Speaker DC power connector and DC power cable w (connects to right speaker DC power q connector) Right speaker with Control knob 9, and connectors for subwoofer - and speaker DC power q Headphone connector (right speaker) 8 Not shown Connecting the Power Cable 1. Read the warning below. Å WARNING: To reduce the risk of electric shock or damage to your equipment: Do not disable the power cord grounding plug. Be sure that the grounded power outlet you plug the power cord into is easily accessible to the operator and located as close to the equipment as possible. A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it. Arrange them so that no one may accidentally step on or trip over them. See "Power Cord Set Requirements" in Appendix B for additional information. 2. Connect one end of the power cable to the monitor 5 and the other end to an electrical wall outlet. The setup test pattern displays. Auto-adjustment setup test pattern 6. Press the Auto/Select button on the monitor front panel to produce a stable, centered image. 4­4 User's Guide Operating the Monitor Front Panel Components The monitor buttons are located on the side of the front panel. A B C D E F Front panel buttons on the vs monitor User's Guide 4­5 Operating the Monitor A B C D E Front panel buttons on the f monitor 4­6 User's Guide Operating the Monitor ` Item Control A Function Menu OSD Menu Active OSD Inactive (Onscreen Display) Button closes OSD. (Also closes setting screens on OSD menu. ) vs monitor: /+ (Vol up/Plus) f monitor: /+ (VGA/Plus) OSD Menu Active Button navigates up or right browse, and adjusts settings up. OSD Inactive vs monitor: Button increases the volume level of the monitor speakers. OSD Inactive vs monitor: Button decreases the volume level of the monitor speakers. OSD Inactive Button starts auto-adjustment, which automatically adjusts the display to the ideal setting. Power light Fully powered: Blue Sleep mode: Amber B C vs monitor: /­ (Vol down/Minus) f monitor: OSD Menu Active Button navigates down or left browse, and adjusts settings down. /­ (DVI/Minus) D Auto/Select OSD Menu Active Button acts as an Enter (Select) key to select setting screen options. Power Switch Turns monitor on and to standby (sleep mode). E Power F (Headphone jack) When the headphones are connected, the monitor speakers are muted. f monitor: Headphone jack is on the right speaker. User's Guide 4­7 Operating the Monitor Using the Onscreen Display 1. If the monitor is not already on, press the Power switch (E) to turn on the monitor. The OSD Main Menu displays. Main Menu Brightness Contrast Auto-Adjustment* Volume** Advanced Menu Exit *Auto-Adjustment appears for VGA connections only. [. . . ] The power cord must be rated for the product and for the voltage and current marked on the product's electrical ratings label. The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product. In addition, the cross-sectional area of the wire must be a minimum of 0. 75 mm² or 18AWG, and the length of the cord must be between 4. 94 ft. If you have questions about the type of power cord to use, contact your HP-authorized service provider. [. . . ]