User manual SONY STR-D1011

[. . . ] Batteries or batteries installed apparatus shall not be exposed to excessive heat such as sunshine, fire or the like. Don't throw away battery with general house waste; dispose of it correctly as chemical waste. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] · OFF This function is not activated. 67GB 4 Using the surround back decoding mode By decoding the surround back signal recorded in Dolby Digital Surround EX, DTSES Matrix, DTS-ES Discrete 6. 1, etc. , format, you can enjoy the surround sound intended by the filmmakers. Press V/v repeatedly to select "SB Dec Mode, " then press . 5 Press V/v repeatedly to select the surround back decoding mode, then press . 1 Tip 2-5 You can select the surround back decoding mode using "SB Decoding" on the Surround settings menu. Using the surround back decoding mode (SB Decoding) 1 Make sure that the AMP button is lit. If it is not lit, or "GUI MODE" is not displayed in the display window of the receiver, follow the steps in "7: Operating the receiver using the GUI (Graphical User Interface)" (page 38). x SB Decoding (Surround back decoding) · AUTO When the input stream contains the 6. 1 channel decode flaga), the appropriate decoding is performed on the surround back signal. Input stream Dolby Digital 5. 1 Dolby Digital Surround EXb) Output Surround back channels decoding 5. 1e) 6. 1e) -- Matrix decoder that confirms to Dolby Digital EX 2 Press V/v repeatedly to select "Settings, " then press or b. The Settings menu list appears on the TV screen. 3 68GB Press V/v repeatedly to select "Surround, " then press or b. Input stream DTS 5. 1 Output Surround back channels decoding 5. 1e) -- DTS Matrix decoding DTS Discrete decoding x SB Dec Mode (Surround back decoding mode) You can select surround back decoding mode only when "SB Decoding" is set to "ON" or "AUTO" and the input stream contains the Dolby Digital Surround EX flag. Parameter Speaker Surround back setting decoding DDEX 7. 1 channels 6. 1 channels PLIIx MV 7. 1 channels 6. 1 channels PLIIx MS 7. 1 channels 6. 1 channels Matrix decoder conforms to Dolby Digital EX Matrix decoder conforms to Dolby Digital EX Movie decoder conforms to Dolby Pro Logic IIx Matrix decoder conforms to Dolby Digital EX Music decoder conforms to Dolby Pro Logic IIx Music decoder conforms to Dolby Pro Logic IIx DTS-ES Matrix 6. 1e) 6. 1c) DTS-ES Discrete 6. 1d) 6. 1e) a) A 6. 1 channel decode flag is information recorded in software, such as DVDs. The Dolby Corporation web page can help you distinguish Surround EX films. c) Software encoded with a flag to denote it has both DTS-ES Matrix and 5. 1 channel signals. d) Software encoded with both 5. 1 channel signals and an extension stream designed for returning those signals to 6. 1 discrete channels. Discrete 6. 1 channel signals are DVD specific signals not used in movie theaters. e) When two surround back speakers are connected, the output channel will be 7. 1 channel signals. b) Enjoying Surround Sound · ON The SB Dec Mode setting is applied to 5. 1 channel and 6. 1 channel decoding in the input stream. · If surround back decoding processing is being performed while the receiver is receiving signals with a sampling frequency of more than 48 kHz, the signals will always be played back at either 44. 1 kHz or 48 kHz. · If surround back decoding processing is being performed while the receiver is receiving DTS 96/ 24 signals, the signals will always be played back at 48 kHz. · There may be no sound from the surround back speaker in Dolby Digital EX mode. Some discs have no Dolby Digital Surround EX flag even though the packages have Dolby Digital EX logos. In this case, select "ON. " · When "PLIIx" of the A. F. D. · SIDE/HIGH Select if the location of your surround speakers corresponds to sections A and D. · BEHD/LOW Select if the location of your surround speakers corresponds to sections B and C. · BEHD/HIGH Select if the location of your surround speakers corresponds to sections B and D. Tip Surround speaker position is designed specifically for implementation of the Cinema Studio EX modes. Those sound fields were designed under the premise that the surround speakers would be located behind the seating position, but presentation remains fairly consistent even with the surround speakers positioned at a rather wide angle. However, if the speakers are pointing toward the listener from the 1 2-5 continued 73GB 1 Make sure that the AMP button is lit. If it is not lit, or "GUI MODE" is not displayed in the display window of the receiver, follow the steps given in "7: Operating the receiver using the GUI (Graphical User Interface)" (page 38). Making settings with the Test Tone menu 2 Press V/v repeatedly to select "Settings, " then press or b. The Settings menu list appears on the TV screen. 1 3 4 Press V/v repeatedly to select "Speaker, " then press . Press V/v repeatedly to select "Speaker Pattern, " then press . Select "Speaker Pattern" according to the speaker system which you are using. You do not need to select the speaker pattern after auto calibration. 2-6 5 Press V/v repeatedly to select the speaker pattern you want. 1 Make sure that the AMP button is lit. If it is not lit, or "GUI MODE" is not displayed in the display window of the receiver, follow the steps given in "7: Operating the receiver using the GUI (Graphical User Interface)" (page 38). 2 Press V/v repeatedly to select "Settings, " then press or b. The Settings menu list appears on the TV screen. 3 4 Press V/v repeatedly to select "Speaker, " then press . Press V/v repeatedly to select "Test Tone, " then press . 74GB Test Tone menu parameters x Test Tone · OFF · AUTO The test tone is output from each speaker in sequence. · FIX You can select which speakers will output the test tone. You can select the test tone type. 5 Select the speaker you want to adjust, then press . The test tone is output from each speaker in sequence. x Phase Noise · OFF · L/R, L/C, C/R, R/SL, R/SR, SR/SL, SR/ SBR, SBR/SBL, SR/SB, SBL/SL, SB/SL, SL/L, L/SR Lets you output the test tone sequentially from adjacent speakers. Some items may not be displayed, depending on the setting of the speaker pattern. 6 Adjust the parameter using V/v, then press . Tips · To adjust the level of all speakers at the same time, press MASTER VOL +/­. [. . . ] · Make sure that cables are correctly and securely connected to components. · Depending on the playback component, component may need to be set up. · Be sure to use a connecting cable for the HDMI jack corresponding to high speed (an HDMI version1. 3a, category 2 cable) when you view images or listen to sound during a DeepColor transmission. · Press SHIFT, then press MENU to show "GUI MODE" on the display. [. . . ]