User manual SONY SPP-A5000

[. . . ] Check with local codes for possible special disposal instructions. Caution You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Privacy of communications may not be ensured when using this phone. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] 14) Lights while the battery is being charged. 2 NEW CALL lamp (p. 51) Flashes when there is a "NEW" data in the Caller ID list. 5 HANDSET LOCATOR button (p. 30) Lights when the handset is in use. 26US Getting Started 6 Getting Started 7 89 6 Antenna (p. 12) continued Getting Started 27US Identifying the parts (continued) Cordless handset 1 2 3 4 5 6 9 0 qa qs 7 8 qd 1 Antenna 2 Speaker 3 Display window (p. 48, 49) Lets you talk between the cordless handsets (when the system has any other additional cordless handsets). 5 HOLD button (p. 31, 58) Switches to a second call if you have "call waiting" service, or lets you make a new call. 8 EZ ACCESS button (p. 21, 31) Lets you make a call with the registered access number. 28US Getting Started Getting Started qh qj qf qk ql w; wa qg qf TONE button (p. 31) Allows you to switch temporarily to tone dialing. ql PGM (program) button (p. 22, 33) Redials one of the last five numbers called/inserts a pause in the dialing sequence. qg RINGER qh I (HEADSET) jack (p. 31) Adjust the cordless handset volume. wa MIC (Microphone) qk # button (p. 56) Used to change the number of digits of the phone number in the Caller ID list. Getting Started 29US Basics Making calls 1 Pick up the cordless handset from the base unit. 2 Press (TALK) and wait until I (HEADSET) jack VOL switch (HOLD) "TALK" appears on the display and the display also shows the talk time in hours, minutes and seconds. Tips · Although the phone number displayed on the redial list is up to 15 digit, the redialing will be successful. · If you redial the same number repeatedly, this number will only be counted as one number of the total five registered numbers that can be redialed. · When dialing from a phone number with a registered name, that name will be displayed in the list in step 2. continued Basics 33US Making calls (continued) To erase the dialed phone number one by one 1 Display the name or phone number you want to erase by doing steps 1 to 3 on page 33. 2 3 Turn Jog Dial to choose "ERASE REDIAL", and then press Jog Dial. You hear a long confirmation beep, and the number is erased. To erase the entire dialed phone numbers at once 1 Press (PGM). 2 3 4 Turn Jog Dial to choose "MEMORY MANAGE", and then press Jog Dial. Turn Jog Dial to choose "ERASE ALL RDL", and then press Jog Dial. Turn Jog Dial to choose "ERASE REDIAL", and then press Jog Dial. You hear a long confirmation beep, and the entire number are erased. To store the dialed phone number into the Phone Directory See page 39. 34US Basics Receiving calls 1 When you hear the phone ring: · Press (TALK). or I (HEADSET) jack VOL switch (HOLD) · Pick up the cordless handset from the base unit when the cordless handset is placed on the base unit. (When Quick talk is set to "ON"; see page 36) "TALK" appears on the display and the display also shows the talk time in hours, minutes and seconds. The IN USE lamp on the base unit lights up. Basics (CALL WAITING/FLASH) (PGM) 2 When you're done talking, press (OFF) or replace the cordless handset on the base unit. The display turns off. Receiving calls when the headset is connected When a headset (optional) is connected to the I (HEADSET) jack on the cordless handset, you can talk through the headset. Open continued Basics 35US Receiving calls (continued) Additional tasks To Adjust the cordless handset volume Put a call on hold*1 Do this Set the VOL switch to H (high), M (middle) or L (low). [. . . ] You hear a beep twice per second and "BATTERY LOW" appears on the display. You hear five short error beeps and "NO OTHER HANDSET REGISTERED" appears on the display. You cannot make a call to an additional cordless handset even if you press (INTERCOM) on the cordless handset and you hear five short error beeps, or the cordless handset does not ring on reception of a call from an additional cordless handset. You cannot assign a station number on the additional cordless handset. · Place the cordless handset on the charger. [. . . ]