User manual SONY RM-LJ304

[. . . ] 4-227-952-13(1) Remote Commander Operating Instructions RM-LJ304 © 2000 by Sony Corporation Precautions On safety Should any solid object or liquid fall into the cabinet, unplug the receiver and have it checked by qualified personnel before operating it any further. Before You Use Your Remote Check that you received the following item with the remote: LR6 (size-AA) alkaline batteries (3) On operation Before connecting other components, be sure to turn off and unplug the receiver. Inserting batteries into the remote Insert three LR6 (size-AA) alkaline batteries with the + and ­ properly oriented in the battery compartment. When using the remote, point it at the remote sensor on the receiver. On cleaning Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine. If you have any question or problem concerning your receiver, please consult your nearest Sony dealer. ] } ] } ] } About This Manual z When to replace batteries The instructions in this manual are for model RM-LJ304. Check your model number by looking at the lower left corner of the front side. [. . . ] If a component is connected to jacks for which they are not originally meant, you can modify the category indication to match the component. For details, see "Programming the Remote" on page 16. z You can turn components on automatically You can set the remote to automatically turn on a component when it is selected from the function list. For details, see "Using the auto power function" on page 21. If you selected a Sony CD changer 1 2 3 Depending on the component that you selected, you may have to do an additional procedure, or you may be able to obtain detailed information about the component by doing an additional procedure. For details, see "Additional procedures after selecting a component" on this page. Move the easy scroll key. Move the easy scroll key to select a disc, then press the key to enter the selection. Start playback. Note If you have changed the discs in the changer, be sure to download the CD memos from the receiver (see page 19) or play the newly inserted disc(s) before you select a disc from the changer. 14 Selecting a Sound Field If you selected the tape deck Move the easy scroll key to display the information about deck A or B. Note When the remote is programmed to control a non-Sony tape deck, the following may occur: -- The information about deck B is not displayed and you cannot switch between tape deck A and B. -- "TAPE A/B" is displayed and tape deck A and B switch automatically each time you press the easy scroll key, etc. Do the procedure below to select a sound field from the sound field list. Note that the sound fields contained in each list will vary depending on the receiver. 1 2 Press SOUND FIELD. Using the Lists Move the easy scroll key to select the sound field, then press the key to enter the selection. A display example If you selected the 2ND AV/2ND AUDIO source Move the easy scroll key to select the source of 2ND AV/ 2ND AUDIO, then press the key. Note Depending on the component you are using, "2ND AUDIO" or "2ND AV" may not be displayed. NORMAL CINEMA CINEMA CINEMA SURROUND ST. EX. A ST. EX. B ST. EX. C To turn off the sound field Move the easy scroll key to select either "2CH STEREO" or "A. F. D. " in the sound field list in the display. The sound field list that is displayed is different depending on the model. 15 Programming the Remote You can customize the remote to match the components connected to your receiver. You can even program the remote to control non-Sony components and also Sony components that the remote is normally unable to control. The procedure below uses as an example a case in which a Kenwood LD player is connected to the VIDEO 2 jacks on the receiver. Before you begin note that: -- You cannot change the settings of TUNER and PHONO. -- The remote can control only components that accept infrared wireless control signals. Be sure to turn on the receiver and point the remote towards the receiver when performing the following procedure. 5 Move the easy scroll key to select the maker of the component ("Kenwood, " for example), then press the key to enter the selection. When programming the remote to control Sony component Select "Sony. " Programming is now completed. Using the Lists To cancel programming Move the easy scroll key to select "EXIT" from the IR SET list, or "CANCEL" from the CATEGORY list or MAKER list, then press the key to enter the selection. z You can freely assign any component to USER 1 and 2 items in the IR SET list 1 Do Steps 1 and 2 in "Programming the Remote". 2 Move the easy scroll key to select "USER 1" or "USER 2, " then press the key to enter the selection. 3 Continue from Step 3 in "Programming the Remote" to select the category and maker of the component. 1 Press SET UP. The set up list appears. IR SET LEARNING DOWNLOAD AUTO POWER 2 Move the easy scroll key to select "IR SET, " then press the key to enter the selection. The IR SET list appears. Note If you select "IR SET" for a component that already has a learned button setting, the learned codes for that component are cleared. Furthermore, if the cleared learned button is used in a Macro Play setting, the setting for that button will be changed to "NO SET". <IR SET> [VIDEO 1 ] [VIDEO 2 ] [VIDEO 3 ] 3 Move the easy scroll key to select the component ("VIDEO 2, " for example), then press the key to enter the selection. [. . . ] The AUTO POWER list appears . To cancel adjusting Select "EXIT" in step 3. <AUTO POWER> ON OFF 3 4 Move the easy scroll key to select "ON" or "OFF", then press the key to enter the selection. When you select "ON", move the easy scroll key to select the video input of the TV, then press the key to enter the selection. Switching the COMMAND MODE 1 2 3 Press SET UP. Move the easy scroll key to select "COMMAND MODE", then press the key to enter the selection. Move the easy scroll key to select "AV SYSTEM1" or "AV SYSTEM2", then press the key to enter the selection. [. . . ]