User manual SONY PS-LX520

[. . . ] The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] · To record with the Dolby NR system on, press DOLBY NR before step 7. · If you hear static while you are recording an AM radio program, remove the rear cover and place the antenna outside (see "To remove the AM antenna" on page 6). + ­ n x N . m X M> Z Note You cannot start recording on the side facing away from you. 1 X x . m/M> 4 l/L TAPE nN j/J DOLBY NR 3 18 1 Tips Press Z PUSH and insert a recorded tape into the cassette holder. With the side you want to play facing towards you n x N AM FM BAND . m X M> ­ TUNE + Z · If you press TAPE nN on the remote when the power is off, the system automatically turns on and starts playing the tape if there is a tape in the holder (One Touch Play). · To switch to the tape while listening to another source, press TAPE nN on the remote while the tape is stopped. The tape will automatically start playing (Automatic Source Selection). · To play a tape recorded with the Dolby NR system, press DOLBY NR on the remote before step 4. ";" appears. Basic Operations 2 3 Press FUNCTION repeatedly until "TAPE" appears. Press DIR MODE on the remote to select "g" to play one side of the tape or "j"* to play both sides repeatedly. * The tape automatically stops after playing back five times. 4 Press N. To start playing the reverse side, press n. The tape starts playing. To Stop playback Pause Do this Press x. With the tape stopped, press . m/M> (or j/J on the remote). Fast-forward or rewind Locate the begining During playback, press of the current or next . m/M> (or track l/L on the remote). Press VOLUME +/­. 19 The CD Player Checking the remaining playing time on the CD Do the procedure below to check the remaining playing time of the current track or the entire CD. Playing CD tracks repeatedly -- Repeat Play The Repeat Play function lets you playback a single track or all the tracks on a CD repeatedly in Normal Play. You can also use Repeat Play function while in Shuffle Play or Program Play. DISPLAY CD REPEAT , Press DISPLAY. Each time you press this button, the display changes as follows: During playback t Current track number and elapsed playing time of the track r Current track number and remaining playing time of the track r Remaining playing time of the entire CD , Press CD REPEAT repeatedly during playback until "REPEAT" appears. Repeat Play starts. ";" appears. 25 Sound Adjustment Generating a more dynamic sound The Dynamic Sound Generator (DSG) automatically enhances your music to produce a more powerful sound. Selecting the sound mode You can enjoy simulated surround stereo effects when you listen to the music near the unit. SURROUND DSG , Press SURROUND. "SURR" appears. To cancel the Surround Press SURROUND again. 26 Other Features Using the Radio Data System (RDS) (European model only) Falling asleep to music -- Sleep Timer The Sleep Timer function lets you specify a sleep time, after which the system stops playing and turns off automatically. You can thus fall asleep to music. What is the Radio Data System? Radio Data System (RDS)* is a broadcasting service that allows radio stations to send additional information along with the regular program signal. Note RDS may not work properly if the station you have tuned in is not transmitting the RDS signal properly or if the signal is weak. * Not all FM stations provide RDS service, nor do they all provide the same types of services. If you are not familiar with the RDS system, check with your local radio stations for details on RDS services in your area. SLEEP Sound Adjustment/Other Features Other Features , Press SLEEP. Each time you press this button, the sleep time changes as follows: AUTO t 90min t 80min t 70min R r OFF T 10min . . . . T 60min Receiving RDS broadcasts , Simply select a station from the FM band. When you tune in a station that provides RDS services, the station name appears in the display. When you choose "AUTO" The system turns off after the current CD or tape finishes playing (up to 100 minutes). The system also turns off when you manually stop the CD or tape. To check the RDS information Each time you press DISPLAY on the remote, the display changes as follows: Station name* Y Clock display (Frequency**) * If the RDS broadcast is not properly received, the station name may not appear in the display. **Pressing DISPLAY on the remote again causes the frequency to appear in the display. To check the remaining sleep time Press SLEEP once. To change the sleep time Press SLEEP repeatedly until the time you want appears. To cancel the Sleep Timer function Press SLEEP repeatedly until "OFF" appears. 27 Waking up to music -- Daily Timer By setting the Daily Timer, you can make the system automatically turn on and off at specified times. To use this function, make sure that you have set the system clock correctly (see "Step 2: Setting the time" on page 7). 4 5 Press l or L repeatedly until "DAILY" apperars. Press ENTER. "ON" appears, then the hour indication flashes. ON 000 10 4, 6, 7, 8 6 5, 6, 7, 9 3 TIMER SELECT Set the starting time. Press l or L repeatedly to set the hour, then press ENTER. [. . . ] Do not use any type of abrasive pad, scouring powder or solvent such as thinner, benzene or alcohol. 32 The remote does not work. · You are not pointing the remote in the direction of the system's sensor. · Make sure that the batteries are inserted correctly. The tape does not record or play, or there is a decrease in sound level. Demagnetize them (see page 32). Speakers Sound comes from only one channel, or the left and right volumes are unbalanced. [. . . ]