User manual SONY MEX-DV1700U

[. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] Example: To set the clock to 10:08 1 Turning off the unit Press (OFF) to stop tape playback or FM/AM reception (the key illumination and display remains on. ) Press (OFF) for two seconds to completely turn off the unit. Note If your car has no ACC position on the ignition key switch, be sure to turn the unit off by pressing (OFF) for two seconds to avoid car battery wear. Press (MENU), then press either side of (PRST/DISC) repeatedly until "CLOCK" appears. 1 Press (ENTER). The hour indication flashes. How to use the menu This unit is operated by selecting items from a menu. To select, first enter the menu mode and choose up/down (+/­ of (PRST/DISC)), or choose left/right (­/+ of (SEEK/AMS)). 2 Press either side of (PRST/DISC) to set the hour. 3 Press (+) side of (SEEK/AMS). (PRST/DISC) (+) : To select upwards The minute indication flashes. SOURCE (­) : To select downwards 4 Press either side of (PRST/DISC) to set the minute. (SEEK/AMS) (­) : To select leftwards SOURCE (+) : To select rightwards 2 Press (ENTER). The clock starts. After the clock setting is complete, the display returns to normal playback mode. Tip When the D. INFO mode is set to ON, the time is always displayed (page 15). 8 Fast-winding the tape Cassette Player Listening to a tape 1 Press (OPEN) and insert a cassette. Playback starts automatically. During playback, press and hold either side of (SEEK/AMS). SOURCE Rewind Fast-forward To start playback during fast-forwarding or rewinding, press (MODE) (o). Locating a specific track -- Automatic Music Sensor (AMS) During playback, press either side of (SEEK/AMS) momentarily for each track you want to skip. You can skip up to nine tracks at one time. 2 Close the front panel. If a cassette is already inserted, to start playback, press (SOURCE) repeatedly until "FWD" or "REV" appears. The side facing up is played. To locate preceding tracks SOURCE To locate succeeding tracks The side facing down is played. Note The AMS function may not work when: -- the blanks between tracks are shorter than four seconds -- there is noise between tracks -- there are long sections of low volume or quiet sections. Tip To change the tape`s playback direction, press (MODE) (o). In the Motion Display mode, all the items are scrolled in the display one by one in order. Tip The Motion Display mode can be turned off. (See "Changing the sound and display settings" on page 15. ) To Stop playback Eject the cassette Press (OFF) (OPEN) then Z 9 Playing a tape in various modes You can play the tape in various modes: ·REP (Repeat Play) repeats the current track. Each time you press (MODE), the band changes as follows: B FM1 B FM2 B FM3 AM2 b AM1b 3 4 Press (MENU), then press either side of (PRST/DISC) repeatedly until "BTM" appears. The unit stores stations in the order of their frequencies on the number buttons. A beep sounds when the setting is stored. Notes · The unit does not store stations with weak signals. If only a few stations can be received, some number buttons will retain their former setting. · When a number is indicated in the display, the unit starts storing stations from the one currently displayed. 11 Receiving the memorized stations 1 2 3 Press (SOURCE) repeatedly to select the tuner. · M. DSPL (Motion Display) ­ to turn the motion display on or off. · A. SCRL (Auto Scroll)*2 (page 17). 1 Select the item you want to adjust by pressing (SOUND) repeatedly. Each time you press (SOUND), the item changes as follows: VOL (volume) t BAS (bass) t TRE (treble) t BAL (left-right) t FAD (front-rear) 2 Adjust the selected item by pressing either side of (SEEK/AMS). When adjusting with the rotary commander, press (SOUND) and rotate the VOL control. 1 2 Press (MENU). Press either side of (PRST/DISC) repeatedly until the desired item appears. Each time you press (­) side of (PRST/DISC), the item changes as follows: CLOCK t BEEP t RM t D. INFO*1 t M. DSPL t A. SCRL*2 *1 When the radio is off, or when no tape, CD, or MD is playing, this item will not appear. *2 When no CD or MD is playing, this item will not appear. Note Adjust within three seconds after selecting the item. GB Note The displayed item will differ depending on the source. Tip You can easily switch among categories ("SET, " "DIS, " "P/M"and "EDT") by pressing an holding either side of (PRST/DISC) for two seconds. 3 4 Press (+) side of (SEEK/AMS) to select the desired setting (Example: ON or OFF). After the mode setting is complete, the display returns to normal playback mode. 15 Boosting the bass sound -- D-bass You can enjoy a clear and powerful bass sound. The D-bass function boosts the low frequency signal and high frequency signal with a sharper curve than conventional bass boost. You can hear the bass line more clearly even while the vocal volume remains the same. [. . . ] If only a few TV channels can be received, some number buttons will remain empty. · When a preset number is indicated in the display, the unit starts storing TV channels from the one currently displayed. Note If you try to store another channel on the same number button, the previously stored channel will be erased. GB Watching the TV or video while listening to a tape, CD or MD -- Simultaneous Play The simultaneous play function does not work while you are listening to the radio. 1 2 3 Press (MENU), then press either side of (PRST/DISC) repeatedly until "SML-SEL" appears. Press (­) side of (SEEK/AMS). continue to next page t 19 4 Press (SOURCE) repeatedly to select CD or MD. Additional Information Maintenance Fuse replacement When replacing the fuse, be sure to use one matching the amperage rating stated on the original fuse. If the fuse blows again after replacement, there may be an internal malfunction. [. . . ]