User manual SONY LBT-D560

[. . . ] Do not expose batteries or apparatus with battery-installed to excessive heat such as sunshine, fire or the like. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately. [. . . ] · Files and folders are played back in alphabetical order in this system. · The system can only play back ­ MP3 files with the extension ". mp3". Note that even when file names have the above file extensions, if the actual file differs, the system may produce noise or may malfunction. The maximum number of audio files and folders may vary depending on the audio file and folder structure. · Compatibility with all encoding/writing softwares, recording devices, and recording media cannot be guaranteed. Incompatible USB device may produce noise or interrupted audio or may not play back at all. · After you have connected the USB device, be sure to handle the USB device with care otherwise it may cause a malfunction. 26GB Playing the iPod You can listen to audio contents stored in the iPod on this system. 1 Press iPod 1 or iPod 2. Using the remote: Press and hold CHANNEL A, then press FUNCTION +/­ repeatedly to select "iPod 1". Press FUNCTION +/­ repeatedly to select "iPod 2". 2 Place the iPod(s). · When placing or removing the iPod, brace the unit with one hand and take care not to press the controls of the iPod by mistake. · Depending on the connected iPod, you may not able to use m or M while playing video. In this case, you can fast rewind or fast forward by holding down l or L (or . · To use an iPod, refer to the operating instructions of your iPod. To exit the OPTIONS menu, press OPTIONS. Set the surround Press SURROUND effect repeatedly until "SURROUND" lights up in the display. * The volume switches to power mode and the equalizer curve changes. Enhancing the sound quality You can enhance the sound quality by using the MP3 BOOSTER+ function. 1 Press OPTIONS. 2 Turn JOG DIAL to select "MP3 BOOSTER+", then press ENTER. 3 Turn JOG DIAL to select "AUTO", then press ENTER. To exit the OPTIONS menu, press OPTIONS. Note When an audio file is played back, the MP3 BOOSTER+ function is automatically activated if you have set "MP3 BOOSTER+" to "AUTO". "BOOSTER" lights up in the display. 29GB Creating a party atmosphere -- Inspiring the DJ's mood Using the beat functions With the beat functions, you can enjoy a variety of rhythms. They can be used with any source. Using the drum pads -- BEAT BLEND With the drum pads, you can add percussion during playback. This effect can be used with any source. To Do this 1 Press BEAT ON/OFF repeatedly to turn off the beat pattern. 2 Hold down BEAT PATTERN and turn JOG DIAL to select the beat pattern you want. 3 Press BPM CONTROL once to start the tempo input. Add the drum sound Change the drum sound Press PAD I or PAD II to produce the respective sound. Hold down PAD I or PAD II, then turn JOG DIAL to select the sound you want. The sound you select will be stored in PAD I or PAD II. 4 By following the tempo of the music, press BPM CONTROL 4 times to input the tempo. Each time you press BPM CONTROL, the flashing "B" will be replaced with a box. Create a drum roll 1 Hold down PAD I and PAD II. 2 Turn JOG DIAL clockwise to output the PAD II sound and counterclockwise to output the PAD I sound. Press BEAT LEVEL repeatedly. 5 Press BPM CONTROL again to start playback of the beat pattern. [. . . ] · Do not expose discs to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight. Cleaning the cabinet Clean this system with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as thinner, benzine, or alcohol. On safety · The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall socket, even if the unit itself has been turned off. · Completely disconnect the power cord (mains lead) from the wall socket (mains) if it is not going to be used for an extended period of time. · Should any solid object or liquid get into the system, unplug the system, and have it checked by qualified personnel before operating it again. Notes on remove/insert the SYSTEM CONTROL cord from/to the unit To prevent the system malfunction or breakdown, do the following procedures: ­ Before connecting the power cord (on the subwoofer) to the wall outlet, be sure to connect the SYSTEM CONTROL cord to the unit and secure with screws of the plug. [. . . ]