User manual SONY BRAVIA KDL-32L5000

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: s Reorient or relocate the receiving antennas. [. . . ] Connect the other plug of the power cord to a wall outlet. Wall outlet For 120 V AC AC IN AC power cord (supplied) 24 Connecting a VCR and Cable TV Use this hookup if: · You subscribe to a cable TV system that does not require a cable box. Disconnect all power sources before making any connections. 1 2 3 Connect the CATV cable to the VCR's IN jack. Using the supplied 75-ohm coaxial cable, connect the VCR's OUT jack to the TV's VHF/UHF jack. Using A/V and S VIDEO cables, connect the VCR's AUDIO and S VIDEO OUT jacks to the TV's AUDIO and S VIDEO IN jacks (VIDEO 1 IN or VIDEO 3 IN). Tip If your VCR is not equipped with S VIDEO, use a VIDEO cable (yellow) instead of the S VIDEO cable. Connecting and Setting the TV 75-ohm coaxial cable (supplied) 75-ohm coaxial cable (supplied) Rear of TV VIDEO IN R AUDIO VIDEO L (MONO) S VIDEO VHF/UHF 1 VCR Cable 3 AUDIO-R (red) AUDIO-L (white) 4 AUDIO HD/DVD IN S VIDEO cable (not supplied) VIDEO (yellow) S VIDEO R L Y PB PR R L (VAR/FIX) AUDIO OUT CENTER SPEAKER IN 180W (6 ) MAX A/V cable (not supplied) Note When you connect video equipment to both the VIDEO and the S VIDEO input jacks, make sure "Auto YC" in the (Setup) menu is set to "On" to view the S VIDEO input (see below). Tip You can also use the VIDEO 2 IN jacks located on the front of the TV to connect your VCR. When connecting both VIDEO IN and S VIDEO IN Using the menu, you can select the jack from which the TV receives the input signal. You can set it for each video input (VIDEO 1 IN, VIDEO 2 IN and VIDEO 3 IN) separately. The TV is factory set to receive S VIDEO input signals. 1 2 3 4 5 Press VIDEO 1/2/3 repeatedly until the desired video input appears. To watch the pictures input from the S VIDEO input jack: Press V/v to select "On, " then press . Press V/v to select "Off, " then press 6 Press MENU to exit the menu screen. 25 Connecting a Satellite Receiver Disconnect all power sources before making any connections. 1 2 Connect the satellite antenna cable to the satellite receiver's SATELLITE IN jack. Using A/V and S VIDEO cables, connect the satellite receiver's AUDIO and S VIDEO OUT jacks to the TV's AUDIO and S VIDEO IN jacks (VIDEO 1 IN or VIDEO 3 IN). Tip If your satellite receiver is not equipped with S VIDEO, use a VIDEO cable (yellow) instead of the S VIDEO cable. 3 Connect the supplied 75-ohm coaxial cable from your cable or antenna to the TV's VHF/UHF jack. Satellite antenna cable Satellite Receiver 75-ohm coaxial cable (supplied) Rear of TV VIDEO IN R AUDIO VIDEO L (MONO) S VIDEO VHF/UHF 1 3 AUDIO-R (red) S VIDEO cable (not supplied) AUDIO-L (white) 4 AUDIO HD/DVD IN R L Y PB PR VIDEO (yellow) S VIDEO A/V cable (not supplied) R L (VAR/FIX) AUDIO OUT CENTER SPEAKER IN 180W (6 ) MAX Note When you connect video equipment to both the VIDEO and the S VIDEO input jacks, make sure "Auto YC" in the (Setup) menu is set to "On" to view the S VIDEO input (see page 25). Tips · You can also use the VIDEO 2 IN jacks located on the front of the TV to connect your satellite receiver. · Use VIDEO 1/2/3 on the remote control to select VIDEO 1 IN (or VIDEO 3 IN if you use the VIDEO 3 IN jacks for this hookup) to watch satellite TV. 26 Connecting a Satellite Receiver and a VCR Disconnect all power sources before making any connections. 1 2 3 4 Connect the satellite antenna cable to the satellite receiver's SATELLITE IN jack. Using the supplied 75-ohm coaxial cable, connect the VCR's OUT jack to the TV's VHF/UHF jack. · If your Digital Satellite Receiver has a DVI-HDTV or HDMI connector, for best picture quality, use the connection described on page 33. Connecting and Setting the TV 3 PR Using an optical digital cable, connect the DVD player or Digital Satellite Receiver's OPTICAL OUT jack to the AV Receiver's OPTICAL IN jack. Rear of TV VIDEO IN R AUDIO VIDEO L (MONO) S VIDEO PB Y 1 3 AUDIO-L (white) AUDIO-R (red) 4 AUDIO HD/DVD IN R L Y PB PR Component video cable (not supplied) AUDIO cable (not supplied) R L (VAR/FIX) AUDIO OUT CENTER SPEAKER IN 180W (6 ) MAX SPEAKER cord (not supplied) FRONT R CENTER FRONT L SUB WOOFER AUDIO OUT SCAN SELECT VIDEO 1 SELECTABLE INTERLACE R AUDIO OUT L VIDEO OUT R VIDEO 2 AUDIO IN L MONITOR OUT VIDEO S VIDEO VIDEO IN AM SURR R SURR L COMPONENT VIDEO OUT SPEAKER R L AUDIO IN VIDEO IN Y PB/CB PR/CR OPTICAL DIGITAL IN FM 75 COAXIAL VIDEO 2 COMPONENT VIDEO OUT DVD Player or Digital Satellite Receiver AV Receiver Optical digital cable (not supplied) When using the TV's speakers as the center speaker Using "Center Speaker Mode" in (Audio) menu, select the video input that you want to use the TV's speakers as the center speaker, and set to "On. " For more details, see "Using the Center Speaker Feature" on page 50. 35 Connecting a Camcorder Disconnect all power sources before making any connections. Using an A/V cable, connect the Camcorder's A/V OUT jack to the TV's AUDIO IN jacks and VIDEO IN jack (VIDEO 2 IN). Tips · You can also use the VIDEO 1 IN and VIDEO 3 IN jacks located on the rear of the TV to connect your camcorder. · If your camcorder has an S Video output connector, for better picture quality, use an S VIDEO cable to connect the camcorder's S VIDEO OUT jack to the TV's S VIDEO IN jack (VIDEO 2 IN). Front of TV S VIDEO (MONO) VIDEO L AUDIO R VIDEO 2 IN VIDEO (yellow) AUDIO-L (white) AUDIO-R (red) Camcorder A/V cable (not supplied) A/V output 36 Setting the TV Setting the Channels After you finish connecting your TV, you can run Auto Program to set up your channels. The Auto Setup menu appears when you turn your TV on for the first time after installing it. The Auto Setup menu automatically appears on the screen when you turn on the TV for the first time. Auto Setup , 2 Auto Program: Exit: [CH+] [CH­] First please connect cable/antenna Connecting and Setting the TV Press CH + on the remote control or on the dropdown panel of your TV to perform Auto Program. When all the receivable channels are stored, the "Channel Skip/Add" menu appears. 1 DVD/ MUTING VCR SAT/ POWER CABLE MODE PICTURE WIDE SLEEP DISPLAY Auto Program is set to scan cable TV channels by default. To watch VHF/UHF channels with an antenna, see "To watch VHF/UHF channels with an antenna" on page 38. To perform Auto Program again 1 Press MENU. 2 Press V/v to select . (Channel), then press 3 Press V/v to select "Auto Program, " then press . 4 Press TOP MENU FAVORITES MENU . "Auto Program" appears and the TV starts scanning and presetting channels automatically. When all the receivable channels are stored, the "Channel Skip/Add" menu appears. Using this menu, you can start skipping unnecessary channels (see "To skip channels" on page 38). 5 Press MENU to exit the menu screen. F1 F2 TV VIDEO 1/2/3 VIDEO 4 VIDEO 5 To cancel Auto Program While "Auto Program" is displayed in step 3, press MENU on the remote control. Note To watch cable TV channels, you have to subscribe to a cable TV company. For details on cable TV subscription, consult your nearest cable TV company. 2 RESET FREEZE MTS/SAP GUIDE TV/SAT (Continued) 37 To watch VHF/UHF channels with an antenna 1 Press MENU. 2 Press V/v to select . (Channel), then press To skip channels You can skip unnecessary channels when selecting channels using the CH +/­ buttons. 3 Press V/v to select "Cable, " then press . [. . . ] Picture (stripe) noise. Possible remedies · Check antenna/cable connections. · Check if the antenna has reached the end of its serviceable life. (3-5 years in normal use, 1-2 years at the seaside. ) · Keep the TV away from noise sources such as cars, motorcycles, or hair-dryers. · Adjust the Picture Mode options in the (Video) menu (page 60). [. . . ]