User manual SONY BRAVIA KDL-32BX310

[. . . ] POWER CORD POLARIZATION: CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the cable TV system installer's attention to Article 820-40 of the National Electric Code (U. S. A. ). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. REGULATORY INFORMATION: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. [. . . ] Select a channel bank with an installer remote - -press SOURCE/BANK (and repeat). Use the ADD/DEL/BLNK item (also in the Setup menu) to customize your program package. You can also "Blank" a channel for accommodating an audio-only program source or in-house communication. Repeat steps 2, and 3 to program another channel bank. CHANNEL BANK Channel Bank Program package BANK 1 1 Basic cable channels 2 Extended cable channels 3 Extended with premium channels 4 Other cable service options (Grouping is provided as an example only. ) Channel Bank Number Display The BLNK (blank) channel function is "global" -- the same channel number is blanked in channel banks 1, 2, 3, and 4. PAGE 26 206-3490-O Managing the Channel Banks Examples of typical channel banks charts Figure 1. Typical channel banks after running Auto Program B Purpose A N K 1 2 3 4 Channel Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A = Active - - Channel was found during AUTO PROGRAM Figure 2. Typical channel banks after running Auto Program, and customizing with Add/Del/Blnk B Purpose A N K 1 2 3 4 Basic Extend All CTV Other Channel Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 BC A BC A BC A BC A A A A A A A A A A A A A A A A A D A A A D D D A D A A A D A A A D D D A D A A A D A A A D A A A D D A A D D D A D D A A D D A A A = Active D = Deleted BC = Blanked Channel Channel was found during AUTO PROGRAM Channel was deleted using Add/ Del option. Channel was blanked using BLANK channel option (ADD/DEL/BLNK). ADDING / DELETING CHANNELS It is best to do ADD / DEL customizing before doing "BLNK. " AUTO PROGRAM enters the same channels in banks 1, 2, 3, and 4. AUTO PROGRAM removes any channels previously customized with ADD / DEL / BLNK. The channels available on your antenna / cable will be entered, and any channels previously entered but not currently available will be deleted. ADD and DEL (not BLNK) can be used independently for channel banks 1, 2, 3, and 4. Channel allocations in tuning bands: BROADCAST: 2 ­ 69 CABLE ­ CATV, HRC or ICC: 1 ­ 125 206-3490-O PAGE 27 Managing the Channel Banks PLAN YOUR CHANNEL BANKS BY FILLING IN THESE CHARTS (or use photocopies). B Purpose A N K 1 2 3 4 Channel Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 B Purpose A N K 1 2 3 4 Channel Number 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 B Purpose A N K 1 2 3 4 Channel Number 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 B Purpose A N K 1 2 3 4 Channel Number 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 B Purpose Channel Number A 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 FM N K 1 2 3 4 PAGE 28 206-3852 Installer's Menus Use the Installer Menu to set up or change operational settings See descriptions of the Installer items on the following pages. . . Accessing the Installer's Menu Installer's menu items can be accessed by using the optional LP702 installer's remote control. Just press and hold MENU (about 8 seconds) until the display changes, then press 9, 8, 7, 6, then ENTER. 86-I. NOT USED DEFEAT XDS NOT USED UPN MSB UPN MSB-1 UPN MSB-2 UPN LSB CHKSM ERROR HANDSHK TIME PERMANENT BLK A. MUTE TIME 0 - 255 0 - 255 0 - 255 0 - 255 0/1 0-5 0/1 0 - 254 0 - 254 255 255 255 255 0 0 0 50 50 User programmable number, most significant byte. Remove block hours setting for Parental Control and make blocks permanent. 0/1 0 When set to 1, XDS display program information will not appear. Detailed Descriptions of Installer Menu Items 0-I. INSTALLER SEQUENCE Gives access to Installer Menu depending on the code selected. 0 = 9876 2 = 1478 1 = 4321 3 = 3698 senting the hours that the TV will remain on, unless there has been activity from either the control panel or remote control. AC ON (AC Power Switchable) Allows the TV to turn ON just by applying AC power. This is desirable when the TV is plugged into a cable box or a power outlet controlled by a wall switch. Use ADJUST to select 0 or 1, where 0 is the default is OFF, and 1 is ON. NOTE: When set to 1 (ON), the TV does not respond to ON/OFF commands from either the remote or the control panel, and the SLEEP TIMER is also nonfunctional. 1-I. POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff. [. . . ] An electronic device that amplifies sound from a television, CD player, VCR, DVD, or other A/V device. A large metal piece of equipment does not always have to be visible to be using an antenna. Auto Program has the Concierge TV automatically find all the channels available in the area. Lets the installer remove channels from the list the guest will scroll through using the guest remote. [. . . ]