User manual SONY ICF-C1000

[. . . ] Hand the battery over to the applicable collection point for the recycling of waste batteries. For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product. If you have any questions or problems concerning your unit, please consult your nearest Sony dealer. Troubleshooting Should any problem persist after you have made the following checks, consult your nearest Sony dealer. The clock flashes "AM 12:00" or "0:00" due to a power interruption. [. . . ] If a power interruption occurs while the battery is weak, the current time and alarm will be erased. Use of another battery may cause a fire or explosion. iPod nano 4th generation (video) iPhone 3G iPod touch 1st generation Replacing the battery 1 Keep the AC plug connected to the AC outlet, remove the screw that secures the battery holder at the bottom of the unit using a screwdriver, and remove the battery holder (See fig. Replace a new battery in the battery holder with the side facing up (See fig. Insert the battery holder back into the unit and secure it with the screw (See fig. Press iPod & iPhone , SNOOZE/ BRIGHTNESS or FM to turn "" off in the display. Use the supplied AC power adaptor only. Failure to use the supplied AC power adaptor may cause the unit to malfunction. Should you notice an abnormality in the AC power adaptor, disconnect it from the AC outlet immediately. iPod nano 3rd generation (video) iPod classic 2 iPhone 3 4 Specifications Time display Model for UK, Australia and New Zealand: 12-hour System Model for other countries/regions: 24-hour system DC IN 8V AC power adaptor (supplied) iPod nano 2nd generation (aluminum) iPod 5th generation (video) iPod nano 1st generation iPod section DC out: 5 V MAX: 500 mA Note When you replace the battery, do not disconnect the AC power adaptor from the unit. Otherwise, current time, alarm and station presets will be erased. iPod mini No Power No Problem is a trademark of Sony Corporation. Features Wake or sleep to iPod/Radio FM digital synthesized tuner 20 Station Presets (20 FM) Brightness Control (High/Mid/Low/Off) Extendable Snooze system from 10 to 60 min Radio section Frequency range Band FM Frequency 87. 5 MHz ­ 108 MHz Channel step 0. 05 MHz iPod 4th generation (color display) iPod 4th generation ©2010 Sony Corporation Printed in China General Speaker Approx. 5 cm (2 inches) dia. , cone type, 16 Power output 0. 8 W (at 10 % harmonic distortion) Power requirements DC IN 8V () 1 A For clock back up: 3V DC, one CR2032 battery Precautions Operate the unit on the power source specified in "Specifications. " To disconnect the AC power cord (mains lead), pull it out by the plug, not the cord. The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. Since a strong magnet is used for the speaker, keep personal credit cards using magnetic coding or spring-wound watches away from the unit to prevent possible damage from the magnet. 6 Press ALARM/CLOCK + or ­ repeatedly until the desired alarm mode flashes. You can choose one of 3 settings: "iPod", "FM" or "BUZZER. " Set the alarm mode as follows: ­ iPod: see " Setting the iPod alarm. " ­ FM: see " Setting the radio alarm. " ­ BUZZER: see " Setting the buzzer alarm. " The alarm mode setting is entered. Press ALARM RESET OFF to turn off the alarm. The alarm will sound again at the same time the next day. AC power adaptor To deactivate the alarm Press ALARM ON/OFF to turn off the "ALARM" indicator from the display. Note on the alarm in the event of a power interruption In the event of a power interruption, the alarm will work until the battery is totally discharged. However, certain functions will be affected as follows: The backlight will not light up. If the alarm mode is set to iPod or radio, it will change to BUZZER automatically. If a power interruption occurs while the alarm is sounding, the alarm will stop. If ALARM RESET OFF is not pressed, the alarm will sound for about 5 minutes. If "" appears in the display, the alarm will not sound in the event of power interruption. During a power interruption, the alarm will sound at the set time only once. To change the display to the daylight saving time (summer time) indication Change the daylight saving time (summer time) adjustment setting according to the following procedures. " " appears in the display and the time indication changes to the daylight saving time (summer time). When using an iPod touch/iPhone To wake up to music stored in an iPod touch/ iPhone, connect the iPod touch/iPhone to the unit first, follow the steps above to set alarm time, and then select the music function. [. . . ] Notes When placing or removing the iPod, hold the iPod at the same angle as that of the connector on this unit, and do not twist or bend the iPod as connector damage may result. When placing or removing the iPod, hold the iPod firmly so as not to topple the unit. Before disconnecting the iPod, pause playback. 3 Press ALARM/CLOCK + or ­ to select 4 Press ALARM ON/OFF. the volume. the desired preset number or "­ ­". "VOL" appears in the display. The display returns to clock mode for about 4 seconds after you have finished the duration setting and released SLEEP, and then the sleep timer starts. [. . . ]