User manual SONY FWD-40LX2F/SI

[. . . ] If you fail to do so, the speakers may come out of the unit and the unit may fall. This can cause injury. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] · If colors appear too light after inputting a DVD signal to the display unit, adjust the "Chroma" setting in the Adjust Picture menu. · When the phase is readjusted, the resolution will be reduced. · The signals from the Macintosh computer will not be guaranteed for recognizing the digital RGB input. · The signals indicated with ** cannot automatically be distinguished from one another. Every time you execute "Auto Adjust" of "Adjust Screen" in the "SCREEN CONTROL" menu, one of the settings for those signals will be applied consequently. Select the appropriate setting. Actual on-screen display of the unit's status On-screen display 640×480 / 60 (e. g. ) 480 / 60i (e. g. ) Significance The selected input signal is computer RGB. The selected input signal is NTSC. PAL NTSC SECAM NTSC4. 43 PAL60 PAL-M PAL-N 575/50I 480/60I 1080/48I 1080/50I 576/50P 480/60P 1080/60I 720/60P 720/50P NTSC (e. g. ) Not Supported Signal The input signal is out of the capture range. No Sync INPUT1 DVI INPUT2 RGB INPUT2 Component Option1/2 Video There is no input signal. The signal mode of OPTION1 or OPTION2 slot is set to analog RGB. Option1/2 S Video Option1/2 RGB Option1/2 Component The signal mode of OPTION1 or OPTION2 slot is set to component video. 24 (GB) Selecting Image Quality / Adjusting the Picture Selecting Image Quality You can set an image quality suitable for the type of picture or the brightness of the location where the unit is installed. Adjusting the Picture While watching the picture, you can adjust contrast, brightness, chroma, phase, and so on, to suit your taste. Set the Picture Mode to any of "User1" to "User3. " 1 Press MENU. The main menu appears on the screen. PICTURE/SOUND CONTROL Picture Mode: Adjust Picture Adjust Sound Standard Adjusting the Contrast, Brightness, Chroma, and Phase, etc. Press MENU to show the main menu and adjust "Contrast, " "Brightness, " "Chroma, " "Phase, " "Sharpness, " "Noise Reduct. , " "Dynamic Picture, " "Color Temp. " or "Gamma Correct. " on the Adjust Picture menu. Select Set ENTER Exit MENU 2 Press M/m to move the cursor (yellow) to "PICTURE/SOUND CONTROL" and press ENTER. Press ENTER to return to the Adjust Picture menu. 2 3 26 (GB) Adjusting the Picture Gamma Correct. Balances the light and dark portions of pictures automatically. Restoring the Adjust Picture Menu Items to Their Original Settings 1 1 Select "Gamma Correct. " with M/m and press ENTER. The following menu appears on the screen. PICTURE/SOUND CONTROL Adjust Picture Gamma Correct. : Reset High Mid Low In the Adjust Picture menu, press M/m to move the cursor (yellow) to "Reset" and press ENTER. The following menu appears on the screen. PICTURE/SOUND CONTROL Adjust Picture Gamma Correct. : Reset Mid Cancel OK Select Set ENTER Exit MENU Select Set ENTER Exit MENU 2 2 Select the Gamma Correct. Press ENTER to return to the Adjust Picture menu. Press M/m to move the cursor (yellow) to "OK" and press ENTER. The Adjust Picture menu items are restored to their factory presettings. Note 3 The values set for Color1 ­ 3 of Color Temp. Alternatively, select "Cancel" with M/m and press ENTER. Notes · You cannot adjust Chroma and Phase when an RGB signal is input. · You cannot adjust Phase with a PAL, PAL-M, PAL-N, PAL60, or SECAM color system. · You cannot adjust Phase when a black-and-white signal is input. 27 (GB) Picture Enlargement Picture Enlargement You can enlarge pictures to suite your taste. Original Picture (Picture Type) Wide Zoom Ordinary pictures with a 4:3 aspect ratio (screen aspect ratio: 4:3). Images are enlarged naturally to full screen size. Setting Auto Wide The Auto Wide function faithfully reproduces images based on the identification control signal to identify the video signal format or enlarges various types of pictures to the optimum. Identification Control Signal This is a control signal for faithfully reproducing the aspect ratio of the original image. [. . . ] To make the display power stay on indefinitely, set this function to "Off". For details on the "Auto Shut Off" function, see "Auto Shut Off" on page 20 (GB). For details on the "On/Off Timer" function, see "On/Off Timer Function" on page 38 (GB). Turn off the power, and make sure that the air vents are not blocked, that there is ample space for air to flow around the display, and that the ventilation in the room is working properly. [. . . ]