User manual SONY EXR-200

[. . . ] · When "CHECK ANTENNA" appears in the display The supplied antenna is not connected to this unit. Check the connection of the antenna cord, then turn the power on again. · When "NO SIGNAL" appears in the display The receiving condition is not good. · When "UPDATING" appears in the display You have not subscribed for XM or the channel is not authorized. [. . . ] 4 1/8 × 2 5/8 × 5 1/8 inches) When the main unit is installed in the home cradle with the home stand: Approx. 220 g (7. 8 oz) When the main unit is installed in the car cradle with the car stand: Approx. 380 g (13. 4 oz) When the main unit is installed in the home cradle with the home stand: Approx. 300 g (10. 6 oz) Cradle release button OWNER'S RECORD The model number is located on the bottom and serial number also on the bottom. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Radio ID To remove the main unit from the cradle While pressing the two cradle release buttons on the left and right sides of the main unit, pull out the main unit from the cradle. Replacing the Lithium Battery into the Remote Commander Replace the battery when the buttons on the remote commander do not work. Remove the old battery and insert a new one. DRN-XM01C DRN-XM01R DRN-XM01H Sony Corporation © 2001 Printed in Japan Features · This unit is exclusively for the XM Satellite radio. · Display function for a variety of text information about the tuned-in channel. · Memo function enables the unit to store the text information for up to 10 memories. · Transportable type receiver, which can be attached and removed from the cradle easily. · Category Scroll function using a specified category for easy channel selection. If the current UTC data is not received, "­ ­ : ­ ­" appears in the display. Using the Category Scrolls In Category Scroll mode, you can search for a channel among authorized channels that have the corresponding Channel Category you selected in the menu display. Checking the Tuned Channel Information This unit has three display modes in the tuned channel display. Using other Functions You can also use the following functions in the menu display. Menu Scroll mode Memo Back Light Beep Time Adjust Contrast Auto Power Down Line Out Level See "Using the Category Scroll" "Storing the Information" below below "Adjusting the Time Difference" below below below Contrast You can adjust the contrast of the display window in 8 levels. The factoryset is level 4. 1 2 1 2 Cradle release button Display window Cradle release button DSPL/BACK MEMO Preset buttons (1-5)* POWER* Remote sensor * The POWER and preset button No. 3 have a tactile dot. 1 2 Press JOG roller (or MENU on the remote) to show the menu display. "SCROLL MODE" appears in the display. 1 Press DSPL/BACK (or DSPL on the remote). The display mode changes as follows: Press POWER to turn on the main unit. After all Additional Information is displayed, "--- + --- + --- + --- +" appears for about 2 seconds and then repeats displaying from the beginning. · As the unit memorizes the display mode when the power is turned off, the display appears in the last display mode when you turn on the unit. Note If the channel has no text information, "--------" will appear in the display. Auto Power Down Auto Power Down function automatically turns off the unit when the specified time passes from the last button operation. The factory-set is "60 min". 1 2 Turn JOG roller (or press X / x on the remote) to adjust the hour and press JOG roller (or ENTER on the remote). The display returns to the tuned channel display. Back Light You can select the lighting level of the display window. The factory-set is "BRIGHT". * Press JOG roller (or MENU on the remote) to show the menu display. Turn JOG roller (or press X / x on the remote) to select "AUTO POWER DOWN" and press JOG roller (or ENTER on the remote). The current setting appears in the display. MENU AUTO BACK ENTER Note This unit does not have the Daylight Saving Time (summer time) function. To cancel a selection Press DSPL/BACK (or BACK on the remote) to return to the previous display during menu operation. [. . . ] · If sound distortion occurs when playing the unit with the cassette adaptor, adjust the Line Out Level. See "Using Other Functions". POWERING DOWN 2 seconds Beep MEMORIZED You can turn the beep on or off. The factory-set is "ON". Presetting your Favorite Channels Preset Tuning You can preset up to 5 channels onto the preset buttons (1­5). To access the preset channels, simply press the corresponding preset buttons (1­5). [. . . ]