User manual SONY CFD-8

[. . . ] · TYPE II (high position) or TYPE IV (metal) tape is being used. · Demagnetize the heads using a commercially available tape head demagnetizer. Record/playback head Capstan Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION With 3. 2-ohm loads, both channels driven from 150 - 6, 300 Hz; rated 1. 8 W per channel-minimum RMS power, with no more than 10 % total harmonic distortion in AC operation. Supplied accessory AC power cord (1) Remote control (1) (CFD-S36 only) Design and specifications are subject to change without notice. WARNING To prevent fire or shock hazard, do not expose the player to rain or moisture. Information For customers in the United States This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Cleaning the cabinet · Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine. 3 2 Select the program source you want to record. To record from the CD player Press CD and insert a CD (See "Playing a CD"). Display c Press SLEEP to select the minutes until the player goes off automatically. Each time you press the button, the indication changes as follows: "60" t "90" t "120" t no indication t "10" t "20" t "30. " Display SLEEP On power sources · For AC operation, use the supplied AC power cord; do not use any other type. · The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off. · Unplug the player from the wall outlet when it is not to be used for an extended period of time. · When the batteries are not to be used, remove them to avoid damage that can be caused by battery leakage or corrosion. · The nameplate indicating operating voltage, power consumption, etc. is located at the bottom. Owner's Record The model number is located at the bottom and the serial number is located in the battery compartment. Refer to them whenever you call upon your Sony dealer regarding this product. Serial No. CD Radio section Erase head Pinch roller Lens Frequency range FM: 87. 6 - 108 MHz AM: 530 - 1, 710 kHz TV: 2 - 13 CH (CFD-S36 USA model only) WEATHER: 1 - 7 CH (CFD-S36 USA model only) Antennas FM/TV/WEATHER: Telescopic antenna AM: Built-in ferrite bar antenna 3 Press N. PLAY CFD-8 CFD-S36 Sony Corporation © 2000 Printed in China CAUTION The use of optical instruments with this product will increase eye hazard. WARNING Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To record from the radio Press RADIO BAND·AUTO PRESET and tune in the station you want (See "Listening to the radio"). Display RADIO BAND AUTO PRESET To cancel the sleep function Press POWER to turn off the power. batteries) Inserting batteries into the remote (CFD-S36 only) Insert two size AA (R6) batteries (not supplied) 1 2 to AC IN Replacing batteries With normal use, the batteries should last for about six months. When the remote no longer operates the player, replace all the batteries with new ones. Note When you operate the player on batteries, you cannot turn on the player using the remote. to a wall outlet · The use of a cassette with more than 90 minutes of play time is not recommended except for long, continuous recording or playback. Using the player on batteries Insert six size D (R20) batteries (not supplied) into the battery compartment. Notes · Replace the batteries when the OPR/BATT indicator dims or when the player stops operating. Before you replace the batteries, be sure to take out the CD from the player. · Do not expose the CD to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight as there can be a considerable rise in temperature inside the car. · Do not stick paper or sticker on the CD, nor scratch the surface of the CD. · After playing, store the CD in its case. If there is a scratch, dirt or fingerprints on the CD, it may cause tracking error. 1 2 3 Press CD. Press the number buttons for the tracks you want to program in the order you want. You can arrange the playing order of up to 20 tracks on a CD. Display Hold down TUNE + or ­ until the frequency digits begin to change in the display. Display TUNE 1 7 2 3 4 9 5 6 8 0/10 >10 MEGA Xpand MEGA BASS MEGA Xpand TAPE TUNE ­, + . , > DISPLAY ENT MEMORY i (headphones) jack MODE OPR/BATT indicator RADIO BAND AUTO PRESET CD . , > MEGA BASS three times the current track number and playing time * For a track whose number is more than 20, the remaining time appears as "- -:- -" in the display. c WEATHER Display (CFD-S36 USA model only) Remote sensor (CFD-S36 only) 3 Locating a specific track Close the CD compartment. To locate a specific track directly PUSH OPEN/CLOSE The player automatically scans the radio frequencies and stops when it finds a clear station. If you can't tune in a station, press the button repeatedly to change the frequency step by step. The new station replaces the old one. Press a number button of the track. [. . . ] To return to normal sound, press the button again. 1 7 2 3 4 9 5 6 8 0/10 >10 To change the current program Press x once if the CD is stopped and twice if the CD is playing. After you've created the program, insert a blank tape and press z to start recording. FM/TV/WEATHER Tip If the FM broadcast is noisy, press MODE until "Mono" appears in the display and the radio will play in monaural. Track number Playing time Repeat Play AM 1 To adjust the volume stop playback pause playback Press VOLUME +, ­ (VOL +, ­ on the remote, CFD-S36 only) x u (X on the remote, CFD-S36 only) Press the button again to resume play after pause. Proceed as follows: To repeat a single track Do this 1 Press MODE until "REP 1" appears. [. . . ]