User manual SNAKEBYTE REMOTE XS CONTROLLER

[. . . ] How to sync in One Time Mode: Press "HOME" on the controller that is synchronised permanently with the console. Select "WII REMOTE SETTINGS" in the upcoming menu, followed by "RECONNECT" Press "1" and "2" simultaneously on the Remote XS Controller which you want to sync with the Wii console in One Time Mode Repeat the above steps for each controller you would like to temporarily sync with your Wii console. The order in which controllers are synced represents the player numbers in multi-player games. Please be aware of the fact that the temporary synchronisation will be erased once the Wii is turned off and that the Standard Mode settings of the respective Remote XS Controller will then be reactivated. [. . . ] Please also pay attention to the appropriate disposal of drained batteries to protect our valuable environment. How to install batteries in your Remote XS Controller Remove the battery cover Insert the batteries into the battery compartment, ensuring the correct placement and polarisation Close the battery cover Proper use of the Remote XS Controller Please fasten the wrist strap onto the fixture in the Remote XS Controller's base and always wear it with a tightened strap lock to avoid accidental slipping. The snakebyte Remote XS Controller's advanced motion sensing technology is highly sensitive: there is no need to move it excessively while playing. The Remote XS Controller can be used in vertical position for Wii games that require its pointer functionality, in horizontal position for classic Virtual Console games, and with accessories such as the Nunchuk and the Classic Controller (Nintendo 1st party originals and respective snakebyte accessories). For further information please refer to your Wii console's and the respective game's manuals. Connecting the Wireless Motion XS Controller Equip your Wireless Motion XS with batteries Connect the Wireless Motion XS receiver with the Extension Connector Port on the Wii Controller Once console and Wii Remote are activated press the Sync button on the Wireless Motion XS to establish a wireless connection between the Motion XS and the receiver. a proper connection is indicated by constantly lighting LEDs on the receiver and the Wireless Motion XS Controller. Proper use of the Wireless Motion XS Controller The Wireless Motion XS can not be used on its own, without the Wii Remote or snakebyte Remote XS. It adds another dimension to Wii gameplay, but only complements the main controller. When using the motion sensing features of the Wii Remote and the Wireless Motion XS please make sure not to move too excessively. Make sure not to lose the Wii Controller and Wireless Motion XS while playing by always wearing the wrist strap and holding both items tightly. Further more you should make sure that there are no interferences between the Remote XS Controller's wireless Bluetooth connection and other wireless devices operating in the 2. Ideally no devices operating in the same room as the Wii console and Remote XS controller should emit radio waves that could potentially interfere with the Remote XS' signal transfer. Use the Remote XS Controller from the optimal operating distance of three metres and make sure there are no objects between controller and sensor bar that could influence the signal transfer. Avoid insolation and other intense light sources behind the TV set and sensor bar in order to maintain the optimal detection of the sensor bar's infrared LED by the Remote XS Controller's camera. Other sources of infrared light such as candles also cause incorrect detection, avoid placing such light sources within Further more pay attention to the sensor bar's correct sensitivity setting in your Wii console's option menu. In case the problem still persists, please restart your Wii console and sync your Remote XS Controller newly. Make sure the batteries in use are not too weak and replace them with fresh ones if required. In many cases pointing the Remote XS Controller off-screen for a few seconds solves the problem. Make sure your main controller is synced with the console and the Motion XS Controller's receiver is firmly attached to the controller's Extension Port. My game seems to receive input signals although I do not even touch the Wireless Motion XS Controller. Turn off your Wii console and turn it on again immediately, this time making sure the analogue thumbstick of the Motion XS Controller remains in its neutral position during startup. [. . . ] If you comply with all instructions and tips, using the products is easy and comfortable. If you don't want to lose your warranty, please refrain from disassembling the controllers ­ there are no user serviceable parts inside anyway. inappropriate handling does invalidate the warranty and leads to malfunctions of the devices. Keep your Remote and Motion XS Controller away from liquids and liquid containers such as vases, bottles, hot baths, jacuzzi tubs, etc. [. . . ]