User manual SIRIUS SIR-ECL1 INSTALLATION GUIDE

[. . . ] Installation Guide Congratulations on your purchase of the SIR-ECL1­ the ECLIPSE Compatible SIRIUS Satellite Radio Tuner! Your new SIRIUS Tuner is designed to work with 2005 and up ECLIPSE E-LAN headunits that are designated "SIRIUS READY. " Contact ECLIPSE or SIRIUS for model compatibility. What is SIRIUS Satellite Radio? Over 120 channels of the best entertainment and completely commercial-free music for your car, home or office. Only SIRIUS has more than 65 original music channels, from today's hits to R&B oldies to classical masterpieces. From authentic country and real bluegrass to cool jazz, hot latin, reggae, rock and many more. SIRIUS also has more than 55 channels of world-class sports, news and entertainment. [. . . ] Mounting the SIR-ECL1 Tuner Be sure that you find a location that is flat and has clearance above the unit to prevent any damage as well as allow for ventilation. Do not install the tuner under the carpet or in a small enclosed area without proper ventilation. Caution: If you are attaching the unit directly to the vehicle's chassis, be sure that you check to make sure the area behind the unit is free from moving parts, fuel or break lines, wire harnesses or any other items which may get damaged by drilling a mounting hole or using the supplied screws. Installing the Antenna The antenna includes a 6-1/2" cable cover/tail which covers the exposed antenna cable and keeps it attached securely to vehicle roof. The tail also helps position the antenna the proper distance from the window, sunroof or rear hatch. To attach the cover/tail: 1) Once you have determined the proper mounting location (see next section), clean the area with the supplied alcohol swab 3) Connect the cover/tail to the antenna cable, making sure that the strainrelief on the antenna seats into the cover/tail groove. Route the cable through the wire channel in the cover/tail. Antenna (Bottom) Adhesive Strips Cable Cover/Tail 6 SIR-ECL1 Installation Guide 4) Remove the protective tape from the adhesive, carefully position the antenna with cover/tail and apply pressure to secure to the vehicle. Antenna Cable Cover/Tail · For SUVs, minivans and five-door vehicles, bring the cable into the vehicle under the rubber molding for the tailgate, and continue under the interior trim. · From the trunk, carefully route the cable to the location of the SIR-ECL1 and plug the SMB connector onto the unit. Sedan/Coupe Vehicle Optimum Antenna Mounting Locations The optimum location to mount the included antenna is on the roof of the vehicle. It is important to avoid any obstruction that will block satellite signal ­ like a roof rack. · Place the antenna on a metal surface of your vehicle at least 12" x 12", and at least 6" from a window. · The antenna's powerful magnet will secure it to the metal surface. The adhesive that is attached to the antenna cover/tail will secure the cable to the vehicle. Before routing the antenna cable, confirm that the antenna is mounted in a good location. · Route the cable from the antenna to the vehicle's interior by tucking it underneath the rubber molding around the rear window (if possible). · Route the cable from the lowest point of the rear window into the trunk. Take advantage of any existing cable channels or wiring conduits. SIR-ECL1 Installation Guide Operation and Installation Guide SUV/Mini-Van Truck Convertible (only) Caution: · Do not pull the wire across sharp edges that could damage it. · Keep the wire away from areas where it could become tangled in the driver's and passenger's feet. · Keep the antenna wire away from extreme heat ­ like exhaust systems. · Avoid placing the cable near any moving parts. 7 7 Wiring and Cable Connections Antenna Input Connect the right-angle SMB connector from the antenna. Push firmly to attach. A E-LAN Output Connector Use the supplied E-LAN cable to connect to the ECLIPSE Headunit ­ See "System Connection Examples" for more specific details. E-LAN Input Connector Connect to optional ECLIPSE audio equipment like CD Changers - See "System Connection Examples" for more specific details. [. . . ] 105mm x 126mm x 35mm (WxHxD) Chassis Size (with Mounting Tabs) . . . . . . . . . . . . . . . . . . . . 4-7/8" x 5" x 1-3/8 (W XHXD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127mm x 126mm x 35mm (WxHxD) Antenna Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mini-Magnetic Antenna Cable Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]