User manual SIM2 SVP 450 PLUS

[. . . ] USER AND INSTALLATION MANUAL MANUALE D'USO E INSTALLAZIONE VIDEO PROJECTOR SVD 500 PLUS SVP 450 PLUS SVP 420 HB SVP 450 PLUS - SVD 500 PLUS INDEX 1WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3 1. 1 Safety and Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. 1 Projector identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The following menu appears: MAIN SETTINGS To change the USER adjustment: change according to the peaking, hue, colour, brightness and contrast required. To store a set of adjustments that will be used by the projector at switching on: use peaking, hue, colour brightness and contarst value to reach a personalized adjustment. The user setup is stored only when the MEMO button is pressed and one of the adjustments is switched on (a small window appears showing a digit that disappears in a few seconds). Press the button EXIT seven times, until the following menu is displayed: INSTALL MODE For instance, to change the contrast value, press for 1 second only, the screen displays the following indication: 1 2 Before adj. REGISTRATIONS be sure the following items have been checked : Mechanical centering of the projector and tubes Lens focus adjustment CON 49 Increase or decrease the value by means of the arrows until the desired value is reached. To store the new value within the USER adjustments, press the button MEMO, the remote control shows the following: STORED CON 49 Press the button ENTER. The following menu appears: INSTALL MODE DEFLECTION Press ESC to let the message disappear or wait 4 seconds and it will disappear on its own. VIDEO SETUP OPTIONS PATTERN SELECT 3. 19 Installation menu The adjustments described in this paragraph must be carried out by qualified personnel. Any adjustments incorrectly done can cause deterioration in picture quality. Note: The following menus operate only in the installation 3. 20 How to enter the installation mode It is only possible in the installation mode to change deflection, adjust the white balance, turn ON/OFF the comb. filter, choose the type of installation and store a setting in the memory banks. Besides carrying out all user adjustments, with the same RC 3100 user remote control it is also possible to carry out all adjustments for a perfect installation and a proper setting of relevant parameters. mode: deflection; video param. ; options and test patterns. Further details about these menus can be found in the section of this manual relevant to installation. Once the installation procedure is through, switch off the projector to exit the installation mode, finally re-start the protection key. 14 SVP 450 PLUS - SVD 500 PLUS 4 INSTALLATION 4. 1 INSTALLATION PROCEDURE Qualified personnel must carefully observe the installation procedure to install the projector and to ensure best performances. Note: The projector is factory-set for front ceiling projection with a 90" screen, 4/3 format and a projector-screen distance of 265 cm. Choose the installation type and read the instructions through carefully. Determine the distance between the screen and the front of the projector. Install the projector on the floor or on the ceiling and center the screen, maintaining the factory deflection settings. If the installation type is the same as the factory setting, go to step 11, otherwise continue. Adjust the magnets. To remove the top cover completely you must unscrew the two locking screws (B) close to the two pivots and the other two (C) securing the jointed rod to the cover. C B 2. 5. 4. 2. 2 Removing the front panel Unscrew the two screws (D) on the left and right of the front panel. To remove the front panel, press the two tongues (F), which are located in its lower portion. 6. Carry out a fine adjustment of the picture with the remote control RC 3000. D 4. 2 Removing the cover 4. 2. 1 Removing the top cover Loosen the 2 securing screws (A) and lift the cover up. D F E F E 4. 3 INSTALLATION TYPES 4. 3. 1 Installation choice A · · · · Choose one of the following possible installation types: DESK TOP FRONT projection DESK TOP REAR projection CEILING FRONT projection CEILING REAR projection 15 ENGLISH SVP 450 PLUS - SVD 500 PLUS 4. 3. 2 Desk-top front projection Correct use of the spacers, as shown in the spacer tables, is mandatory for a perfect focus uniformity. The projector bottom must be parallel with the floor SCREEN - Measure the screen diagonal and take the nearest value from the table. [. . . ] On screen display ON/OFF (only for contrast, brightness, colour, peaking and hue). 6. 5 Light output Large area high brightness (100% white) (900 lumen at white peak). - 6. 6 Projector video resolution RGB VIDEO input: more than 1000 TV lines. - 6. 7 Colour temperature 3200, 6500, 9300 Kelvin degrees instrumentally adjusted by the manufacturer, plus a memory adjustable at will. The colour temperature can be selected and adjusted by means of the remote control. - - 38 SVP 450 PLUS - SVD 500 PLUS 7 DISPLAY PERFORMANCES 7. 1 Flyback time Horizontal 5, 4 µs tip. [. . . ]