User manual SIM2 HT300 XTRA

[. . . ] User and Installation Manual The home theater projector HT300 XTRA cod. 46. 0328. 000 BACK LIGHT Turn on the back light LIGHT STAND-BY Switches off to stand-by. ESCAPE Deactivates the On Screen Display. SOURCE Displays the Source Selection menu. Not active in this model. Up/Down/Left/Right Arrow keys Navigate through and make adjustments to the On Screen menus. Navigates menu pages. FREEZE Freezes a moving picture. ZOOM Not active in this model. F1 F1 Select lens zoom adjustment F2 Select focus lens adjustment AUTO Selects Auto Adjust (automatic optimisation of the displayed image). INFO F2 FOCUS Displays the selected source information and the projector status. VCR Improves the video recorder signals quality. ASPECT Selects image Aspect ratio. XTRA 1 INTRODUCTION Congratulations and thank you for choosing the HT 300 XTRA, a SIM2 Multimedia SpA product (Fig. [. . . ] 24 The projector is equipped with two outputs (Voltage: 12 Vdc) for motorised projection screen and screen masking systems. These 12V outputs should be connected to the appropriate screen interface provided by the screen manufacturer (Fig. The +12V output is activated when the projector is switched on (green LED on) and is de-activated when the projector is in stand-by mode (red LED on). Fig. 22 Connect/disconnect the special Remote Input Interface cable only when the projector is switched off and disconnected from the mains (switch in position O). 12 XTRA The output can be used to control a screen masking system; its output can be set with the "Screen control" adjustment in the "Aspect" menu. This output allows reduction in the area of a 16:9 screen, into a 4:3 format, by activating a screen masking system (refer to screen manufacturer for further information). C SYN DVI RS232 INTERFACE CONNECTOR It is possible to control the projector through a personal computer. First, load the appropriate projector control software onto your PC, then simply connect this input to a cable from your PC's RS232 serial port (Fig. 25 7 KEYBOARD PAD Eight push buttons, at the rear of the projector, will allow complete operation without the use of the remote control. Menu Switches off to stand-by. Navigates Menu pages. Auto Selects Auto Adjust (automatic optimisation of the displayed image). Up/Down/Left/Right arrow keys Navigate through and make adjustments to the On Screen menus. Arrow Up/Down switch on from stand-by and recall Source Selection menu. -Focus-Esc De-activates the On Screen Display and gives access to the lens Zoom/Focus adjustment functions. 13 XTRA 8 REMOTE CONTROL Insert the batteries, taking care to match the polarity, as indicated in the battery recess of the remote (Fig. The remote control sends commands to the projector via infrared signals. It is possible to control the projector by pointing the remote control at the screen; the sensor at the front of the projector will pick up the reflected infrared commands. 27). + + + + - four 1. 5V AAA alkaline batteries DVI C-SYNC LIGHT Fig. 26 ZOOM F1 Change the batteries in the remote control if experiencing difficulty in sending commands to the projector. If the remote control is not to be used for a long period of time remove the batteries. Replace all batteries at the same time; do not replace one new battery with a used battery. If the batteries have leaked, carefully wipe the case clean and replace with new batteries. Fig. 27 Avoid placing obstructions between the remote control and the infrared sensor at the front of the projector; this will impair the remote control performance. 14 XTRA 9 ON SCREEN MENUS SOURCE SELECTION The Source Selection menu is recalled by pressing the key: 0/AV of the remote control or the Up/Down Arrow key of the keyboard pad. Alternatively, use the remote control to directly select the required source (1 to 8). Source Selection 1 2 3 4 5 6 7 8 0 Video S-Video RGBS 15 kHz YCrCb 15 kHz RGBS 32 kHz YCrCb 32 kHz Graphics RGB DVI-D RI2 inputs Video NTSC/60Hz Normal Fig. 28 MAIN MENU To access the main On Screen Display menu, press the Menu key on the keyboard or the key Menu + or Menu - on the remote control (Fig. The main menu is divided into four sections to cover various adjustments in a practical and logical manner. The on-screen menu layout is dependant upon the chosen input signal so various options may not be applicable, i. e. [. . . ] - Adjust the width and height of image, selecting Aspect in the Image Adjustments menu. Image too dark, too pale or unnaturally coloured - Verify compatibility of video/graphic signals with technical specifications of your projector. - Go to Picture menu, select and regulate any of the following, accordingly: Contrast, Brightness, Color, and Tint. - If necessary, reset the Color Temperature and Gamma Correction (found on the Image Adjustments / Advanced Settings menu). Remote control does not work - Check the batteries and for correct polarity. [. . . ]