User manual SIM2 HT300 LINK

[. . . ] User and Installation Manual The home theater projector HT300 LINK cod. 46. 0327. 100 BACK LIGHT Turn on the back light LIGHT STAND-BY Switches off to stand-by. ESCAPE Deactivates the On Screen Display. SOURCE Displays the Source Selection menu. Not active in this model. Up/Down/Left/Right Arrow keys Navigate through and make adjustments to the On Screen menus. Navigates menu pages. FREEZE Freezes a moving picture. ZOOM Not active in this model. F1 F1 function key programmable via OSD F2 function key programmable via OSD AUTO Selects Auto Adjust (automatic optimisation of the displayed image). INFO F2 FOCUS Displays the selected source information and the projector status. VCR Improves the video recorder signals quality. ASPECT Selects image Aspect ratio. 1 INTRODUCTION Congratulations on your choice of the SIM2 Grand Cinema HT300 LINK system! DIGIOPTIC TM IMAGE PROCESSOR TM ON 1 2 3 - OFF PTIC DIGIO LINK UCT R PROD S1 CLAS LASE 1 The HT300 LINK system combines the signal processing capabilities of the DigiOpticTM Image Processor with the high fidelity reproduction of the DLPTM technology Projector by linking the two units via a fibre optic cable. [. . . ] Fom the SETUP menu it is possible to choose to visualize or not this information, for more details check the "SOURCE INFORMATION" in "MENU" section. YCrCb 32kHz RGBS 15kHz YCrCb YCrCb 15kHz YCrCb Fig. 18a Inputs 1 2 3 4 5 6 7 8 9 10 11 12 VIDEO 1 VIDEO 2 S-VIDEO 3 S-VIDEO 4 COMP/RGB 5 COMP/RGB 6 COMP/RGB 7 COMP/RGB 8 GRAPH RGB 9 GRAPH RGB 10 DVI-D 11 DIGITAL INPUT 12 1 2 3 4 5 6 7 8 9 10 11 12 YCrCb 32kHz RGBS 15kHz RGBS 15kHz YCrCb RGBS YCrCb 15kHz YCrCb 15kHz YCrCb YCrCb Fig. 18b 16 MAIN MENU Image Aspect Colour Temperature Gamma Correction Overscan Position Y/C Delay Normal Anamorphic Letterbox Panoramic Pixel to pixel User 1 User 2 User 3 To access the main menu of the On Screen Display press the MENU key on the keypad or the MENU+ or MENU- key on the remote control. The main menu is divided into four windows, PICTURE, IMAGE, SETUP and MENU, in which the various adjustments are grouped according to the frequency of use. Use and to select the line corresponding to the adjustment you wish to make (Fig. 19). Picture Brightness Contrast Colour Tint Sharpness Filter Cinema Mode Video Type Noise Reduction 60 50 50 50 3 2 Off Normal Auto 1 Fig. 20b These submenus are accessed by pressing the key, while exit and return to the upper level occurs by pressing MENU+/-. Press ESC on the remote control or keypad to interrupt the menu display or wait for it to disappear automatically after the number of seconds set on the SETUP page. PICTURE Auto VCR1 VCR2 Fig. 19 The various menus only offer the relevant adjustments in accordance with the type of input signal displayed (e. g. certain typical adjustments for video signals, not necessary for graphic signals, do not appear on the menus, and vice versa). BRIGHTNESS and CONTRAST) are associated with a numerical value that can be varied within the set limits using the keys / . VIDEO TYPE) you can choose among three options presented on the same / ). Other adjustments (marked by the < symbol) provide submenus, which appear as a superimposed window in which the selection is made with the / keys (Fig. Adjustments that are not available for a given input do not appear on the menu. For a complete overview of the onscreen menus, consult the `On screen menu layout' in the "Additional Information" section. BRIGHTNESS Use this control to adjust the image's black level without affecting white areas. Increasing the value will give more detail in darker parts of the picture. For correct adjustment it may prove useful to display the signal relative to the grey scale within which the black level and the level immediately above it must be separately identifiable. Alternatively use a scene composed of black objects alongside other dark coloured objects. CONTRAST Use this control to adjust the image's black level without affecting white areas. To ensure correct adjustment, it may prove useful to display the signal relative to the grey scale, within which the white level and the level immediately below it must be separately identifiable. Alternatively use a scene composed of well-lit white objects surrounded by light coloured objects with lower level lighting. [. . . ] - Adjust the horizontal and vertical position of projected image by selecting POSITION on the IMAGE ADJUSTMENTS menu. - Adjust the width and height of image, selecting ASPECT in the IMAGE ADJUSTMENTS menu. Image too dark, too pale or unnaturally coloured 25 Video Image showing colour misalignment on vertical details - Verify compatibility of video/graphic signals with technical specifications of your projector. - Adjust Y/C DELAY settings in the IMAGE ADJUSTMENTS / ADVANCED SETTINGS to reduce colour misalignment. [. . . ]