User manual SIM2 DOMINO 20 INSTALL GUIDE

[. . . ] Up/Down/Left/Right Arrow keys Navigate through and make adjustments to the On Screen menus. Navigates menu pages. SOURCE Displays the Source Selection menu. MENU Activates the On Screen Display menus. AUTO Selects Auto Adjust (automatic optimisation of the displayed image). INFO Displays the selected source information and the projector status. ASPECT Selects image Aspect ratio. 20 1 INTRODUCTION Congratulations and thank you for choosing the a SIM2 Multimedia SpA product (Fig. [. . . ] This input accepts a Horizontal Scan Frequency of NC C-SY RGSB - YSCRCB COMPONENT VIDEO Fig. 19 This input is suitable for a RGB video signal, or for a Component (YCrCb) type, with composite synchronisation on the green signal (RGsB) or on the luminance (Y) signal (YsCrCb) through a cable with RCA/Phono type connector (Fig. 11 20 Only horizontal scanning frequencies of 15 kHz (standard video resolution) or 32 kHz (high definition video, with progressive scanning) can be applied to this input. MOTORISED PROJECTION SCREEN OUTPUT RS232 INTERFACE CONNECTOR It is possible to control the projector through a personal computer. First, load the appropriate projector control software onto your PC, then simply connect this input to a cable from your PC's RS232 serial port (Fig. 20 The projector is equipped with one output (Voltage: 12 Vdc) for motorised projection screen and screen. This 12V output should be connected to the appropriate screen interface provided by the screen manufacturer (Fig. The +12V output is activated when the projector is switched on (green LED on) and is de-activated when the projector is in stand-by mode (red LED on). Fig. 21 12 20 7 KEYBOARD PAD Eight push buttons, at the rear of the projector, will allow complete operation without the use of the remote control. Auto Selects Auto Adjust (automatic optimisation of the displayed image). Up/Down/Left/Right arrow keys Navigate through and make adjustments to the On Screen menus. Arrow Up/Down switch on from stand-by and recall Source Selection menu. -Focus-Esc De-activates the On Screen Display and gives access to the lens Zoom/Focus adjustment functions. 8 REMOTE CONTROL Insert the batteries, taking care to match the polarity, as indicated in the battery recess of the remote (Fig. batteries have leaked, carefully wipe the case clean and replace with new batteries. DVI + + + + - four 1. 5V AAA alkaline batteries Fig. 22 Change the batteries in the remote control if experiencing difficulty in sending commands to the projector. If the remote control is not to be used for a long period of time remove the batteries. Replace all batteries at the same time; do not replace one new battery with a used battery. If the The remote control sends commands to the projector via infrared signals. 23 pointing the remote control at the screen; the sensor at the front of the projector will pick up the reflected infrared commands. Avoid placing obstructions between the remote control and the infrared sensor at the front of the projector; this will impair the remote control performance. C-SYNC 13 20 9 ON SCREEN MENUS SOURCE SELECTION The Source Selection menu is recalled by pressing the key: 0/AV of the remote control or the Up/Down Arrow key of the keyboard pad. Alternatively, use the remote control to directly select the required source (1 to 8). Source Selection 1 2 3 4 5 6 7 Video S-Video RGBS 15 kHz YCrCb 15 kHz RGBS 32 kHz YCrCb 32 kHz Graphics RGB The main menu is divided into four sections to cover various adjustments in a practical and logical manner. The on-screen menu layout is dependant upon the chosen input signal so various options may not be applicable, i. e. some typical adjustments to the video signal are not applicable to the graphic RGB signals from PC and viceversa. PICTURE When a new source is selected a box appears on the screen with the following indications: selected source, standard video (for video signals), resolution (for graphic signals) and aspect (Fig. 24). Video NTSC/60Hz Normale This menu features adjustments relating to the projected image quality. PICTURE BRIGHTNESS CONTRAST COLOR SHARPNESS FILTER CINEMA MODE VIDEO TYPE 20 50 50 7 6 Off Auto Normal VCR VIDEO Fig. [. . . ] - Should the problem be present with a signal coming from a video-recorder, ensure that the videotape is an Original "first generation" copy and in good condition. - Adjust the VCR's tracking control for optimum picture performance. Incomplete image along borders (vertical and horizontal) - Compare compatibility of video/graphic signals and technical specifications of your projector. - Press Auto (on your remote or keypad) to execute automatic adjustments. [. . . ]