User manual SIM2 DOMINO 18

[. . . ] User and installation manual cod. 46. 0444. 000 STAND-BY Switches off to stand-by. 0-9 Keys SOURCE Displays the Source Selection menu. Switch on from stand-by and allow direct source selection. ESCAPE Deactivates the On Screen Display. Not active in this model. Up/Down/Left/Right Arrow keys Navigate through and make adjustments to the On Screen menus. Navigates menu pages. MENU + Activates the On Screen Display menus. [. . . ] MOTORISED PROJECTION SCREEN OUTPUT RS232 INTERFACE CONNECTOR It is possible to control the projector through a personal computer. First, load the appropriate projector control software onto your PC, then simply connect this input to a cable from your PC's RS232 serial port (Fig. 20 The projector is equipped with one output (Voltage: 12 Vdc) for motorised projection screen and screen. This 12V output should be connected to the appropriate screen interface provided by the screen manufacturer (Fig. The +12V output is activated when the projector is switched on (green LED on) and is de-activated when the projector is in stand-by mode (red LED on). Fig. 21 12 7 KEYBOARD PAD Eight push buttons, at the rear of the projector, will allow complete operation without the use of the remote control. Auto Selects Auto Adjust (automatic optimisation of the displayed image). Switches off to stand-by. Up/Down/Left/Right arrow keys Navigate through and make adjustments to the On Screen menus. Arrow Up/Down switch on from stand-by and recall Source Selection menu. -Focus-Esc De-activates the On Screen Display and gives access to the lens Zoom/Focus adjustment functions. 8 REMOTE CONTROL Insert the batteries, taking care to match the polarity, as indicated in the battery recess of the remote (Fig. batteries have leaked, carefully wipe the case clean and replace with new batteries. DVI + + + + - four 1. 5V AAA alkaline batteries Fig. 22 Change the batteries in the remote control if experiencing difficulty in sending commands to the projector. If the remote control is not to be used for a long period of time remove the batteries. Replace all batteries at the same time; do not replace one new battery with a used battery. If the The remote control sends commands to the projector via infrared signals. 23 pointing the remote control at the screen; the sensor at the front of the projector will pick up the reflected infrared commands. Avoid placing obstructions between the remote control and the infrared sensor at the front of the projector; this will impair the remote control performance. C-SYNC 13 9 ON SCREEN MENUS SOURCE SELECTION The Source Selection menu is recalled by pressing the key: 0/AV of the remote control or the Up/Down Arrow key of the keyboard pad. Alternatively, use the remote control to directly select the required source (1 to 8). Source Selection 1 2 3 4 5 6 7 Video S-Video RGBS 15 kHz YCrCb 15 kHz RGBS 32 kHz YCrCb 32 kHz Graphics RGB The main menu is divided into four sections to cover various adjustments in a practical and logical manner. The on-screen menu layout is dependant upon the chosen input signal so various options may not be applicable, i. e. some typical adjustments to the video signal are not applicable to the graphic RGB signals from PC and viceversa. PICTURE When a new source is selected a box appears on the screen with the following indications: selected source, standard video (for video signals), resolution (for graphic signals) and aspect (Fig. 24). Video NTSC/60Hz Normale This menu features adjustments relating to the projected image quality. PICTURE BRIGHTNESS CONTRAST COLOR SHARPNESS FILTER CINEMA MODE VIDEO TYPE 20 50 50 7 6 Off Normal Auto VCR1 VCR2 VIDEO Fig. 24 MAIN MENU To access the main On Screen Display menu, press the Menu key on the keyboard or the key Menu + or Menu - on the remote control (Fig. 14 PICTURE BRIGHTNESS CONTRAST COLOR TINT SHARPNESS FILTER CINEMA MODE VIDEO TYPE 20 50 50 85 7 6 Off Normal Auto VCR1 VCR2 VIDEO-NTSC PICTURE BRIGHTNESS 50 CONTRAST 20 SHARPNESS 5 SHARPNESS MODE Video Graphics SHARPNESS MODE It allows to select the type of processing that determines the detail. In progressive or de-interlaced video signals the Video option is suggested, with graphic signals from a PC the Graphic option is suggested. [. . . ] - Press Auto (on your remote or keypad) to execute automatic adjustments. - Adjust Frequency and Phase parameters, found in the Image Adjustments menu, to optimise vertical detail of the projected image. Video Image showing colour misalignment on vertical details - Verify compatibility of video/graphic signals with technical specifications of your projector. - Adjust Y/C Delay settings in the Image Adjustments / Advanced Settings to reduce colour misalignment. Remote control does not work - Check the batteries and for correct polarity. [. . . ]