User manual SHERWOOD NEWCASTLE R-965

[. . . ] R-965 Audio/Video Receiver Introduction READ THIS BEFORE OPERATING YOUR UNIT This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Note to CATV System Installer : This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as pracitcal. FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] · The desired mode can be selected with pressing the CURSOR LEFT ( ) button only when the OSD menu operation is not performed. 31 Continued · While listening with headphones, select the desired Dolby Headphone mode. · Each time this button is pressed, the mode changes as follows : STANDBY POWER ON PAGE MAIN FAV CH. SET VOL MUTE CH/ ADJUST DECODE or DSP DSP RETURN STEREO 1 4 7 DISP 2 5 8 0 M2 3 6 9 OSD/MENU ENT MI M3 DOLBY HEADPHONE 1: This simulates the soundfield as if you were in a relatively small room with less reverberations. DOLBY HEADPHONE 2: This simulates the soundfield as if you were in a typical listening room with moderate reverberations. DOLBY HEADPHONE 3: This simulates the soundfield as if you were in a large space like theater. Off : Depending on the signal format which is being input, either the stereo mode or the 2CH downmix mode is selected. RNC-510 · Combined with the current mode, the selected Dolby Headphone mode is activated. · The desired mode can be selected with pressing the CURSOR UP( ) button only when the OSD menu operation is not performed. Notes : · In case of that the original surround mode is "DOLBY DIGITAL EX" or "DTS ES" mode, it will be automatically changed to "DOLBY DIGITAL" or "DTS" mode. · Only when playing a stereo (2 channel) source in "PL IIx", "DOLBY VS" or "DOLBY HEADPHONE" mode, you can select the original surround mode to be combined with use of the MULTI CONTROL knob or the DSP MODE UP( )/DOWN( ) buttons. (However, in case of "PL IIx" mode, you cannot select "PL II"mode. ) · When "PL IIx" mode is selected while playing in "PL II" mode, it will be automatically changed to "DOLBY DIGITAL" or "BYPASS" mode depending on the signal format which is being input. Selecting the desired surround speakers for different program sources · When two sets of surround speakers are connected to the SURROUND A and B speaker terminals and are installed as described in "Speaker placement" on page 11, to achieve more effective surround sound depending on whether program source is movie or music and the different surround modes for the two types of sources, you can select the desired surround speakers. · Each time this button is pressed, the surround speakers are selected as follows : STANDBY POWER ON AUD2 SLEEP DIMM ROOM2 T. TON OSD D/A S. A/B SUR. B PURE Surround A : When using surround speakers A for watching movies. (" " lights up) PARA. PAGE1 Surround B : When using surround speakers B for playing multi-channel (" " lights up) music. Surround A and B : When using both surround speakers A and B. (" " light up) Selecting the surround back channel mode as connected · You can set the surround back channel mode according to surround back speaker connection. · Each time this button is pressed, the mode changes as follows : STANDBY POWER ON AUD2 SLEEP DIMM ROOM2 T. TON OSD D/A S. A/B SUR. B PURE 1 channel : When a surround back speaker is connected. (" SB " lights up) 2 channel : When two surround back speakers are connected. (" SB PARA. PAGE1 " lights up) None : When surround back speakers are not connected. Note: When the power amplifier for surround back channels is assigned to "ROOM2" or the surround speakers are all set to "None", the surround back channel is automatically set to None. 32 ENGLISH To listen in a Dolby Headphone mode · The Dolby Headphone function simulates 5. 1 channel surround sound, which allows you to enjoy 5. 1 channel surround sound through 2 channel headphones, just like listening from 5. 1 channel speakers. Note : Only when the HEADPHONE SELECTOR button is set to the speaker off mode, the Dolby Headphone mode can be selected. Adjusting each channel level with test tone · The volume level of each channel can be adjusted easily with the test tone function. Note: When speakers are switched off , the test tone function does not work. · The test tone will be heard from the speaker of each channel for 2 seconds as follows: FL Front Left STANDBY POWER ON ENGLISH 1 AUD2 SLEEP DIMM ROOM2 T. TON OSD D/A S. A/B SUR. B PURE PARA. PAGE1 FC Center FR Front Right SR Surround Right SUB SUBwoofer SL ( SC) or ( BL BR) Surround Left (Surround Center) (Surr. Back Right) · Depending on the speaker setting(None or No), the test tone of the corresponding channel is not available. · ( ): possible depending on whether the surround back channel is set to 2 CH or 1 CH. Cancel the test tone function. 2 At each channel, adjust the level as desired until the sound level of each speaker is heard to be equally loud. STANDBY POWER ON 3 STANDBY POWER ON AUD2 SLEEP PAGE D/A S. A/B SUR. B PURE DIMM MAIN FAV CH. SET ROOM2 CH/ ADJUST VOL or DOWN UP MUTE CH/ ADJUST DECODE DSP DSP T. TON OSD PARA. [. . . ] SET VOL MUTE CH/ ADJUST DECODE DSP DSP PAGE MAIN FAV CH. SET RETURN CH/ ADJUST VOL MUTE STEREO 1 4 7 DISP 2 5 8 0 M2 3 6 9 OSD/MENU ENT DECODE DSP DSP MI RETURN STEREO M3 1 4 7 DISP 2 5 8 0 M2 3 6 9 OSD/MENU ENT RNC-510 MI M3 · Each time these buttons are pressed, the ROOM 2 FEED mode is changed to "On" or "Off". · When the ROOM 2 FEED mode is set to "Off", the ROOM 2 source cannot be selected. · When you do not use the ROOM 2 function, set the ROOM 2 FEED mode to Off to save electricity. When the ROOM 2 FEED mode is set to On 3 Press the CURSOR UP( )/DOWN( )/LEFT( )/RIGHT( ) buttons to select the desired ROOM 2 source, then press the ENTER button. STANDBY POWER ON PAGE MAIN FAV CH. [. . . ]